American Dryer Corp. Gas/HSI & Steam ID-120 Скачать руководство пользователя

Страница: 19 / 54

NOTE:

Component failure due to dry cleaning solvent fumes will VOID THE WARRANTY.

E. EXHAUST REQUIREMENTS

1. General Exhaust Ductwork Information

Exhaust ductwork

should be

designed and installed by a qualified professional. Improperly sized ductwork

will create excessive back pressure which results in slow drying, increased use of energy, over heating of

the dryer, and shutdown of the burner by the airflow (sail) switches, burner hi-limits, or basket (tumbler) hi-

heat thermostats. The dryer

must be

installed with a proper exhaust duct connection to the outside.

CAUTION:

This dryer produces combustible lint and

must be

exhausted to the outdoors.

CAUTION:

DRYER

MUST BE

EXHAUSTED TO THE OUTDOORS.

CAUTION: IMPROPERLY

SIZED

INSTALLED

EXHAUST

DUCTWORK

CAN

CREATE

POTENTIAL

FIRE

HAZARD

NOTE:

When a dryer is exhausted separately,

recommended

that a back draft damper be

installed.

NOTE:

When dryers are exhausted into a multiple (common) exhaust line, each dryer

must be

supplied with a back draft damper.

The ductwork

should be

laid out in such a way that the ductwork travels as directly as possible to the

outdoors with as few turns as possible. Single or independent dryer venting is recommended.

When single dryer venting is used, for horizontal ducting the minimum duct size is 16-inches (40.64 cm) in

diameter, the duct run should not have more than one (1) elbow (including outside protection), and

must

not exceed

40 feet (12.2 meters) in total length. With single dryer vertical ducting, the minimum duct size

is 18-inches (45.72 cm) in diameter, and the duct run

should

not

have more than three (3) elbows (including

outside protection), and

must not exceed

20 feet (6.1 meters) in total length.

In the case of multiple (common) dryer venting, the distance from the last dryer to the outside exhaust duct

outlet

must not exceed

20 feet (6.1 meters), and have no more than one (1) elbow (including outside

protection).

The shape of the ductwork is not critical so long as the minimum cross-sectional area is provided. It is

suggested that the use of 90º turns be avoided; use 30º and/or 45º bends/angles instead. The radius of the

elbows

should preferably be

1-1/2 times the diameter of the duct. Including basket (tumbler)/dryer

elbow connections or elbows used for outside protection from the weather, the limits noted above

must be

observed. If more elbows are used, the cross-sectional area of the ductwork

must be

increased in proportion

to the number of elbows used.

IMPORTANT:

When the ductwork approaches the maximum limits noted in this manual, a

professional heating, venting, and air conditioning (HVAC) firm

must be

consulted for

proper venting information.

Содержание Gas/HSI & Steam ID-120























































Результаты поиска

Содержание Gas/HSI & Steam ID-120

Отзывы:

Похожие инструкции для Gas/HSI & Steam ID-120

Бренды по названию

Популярные бренды

American Dryer Corp. Gas/HSI & Steam ID-120, Руководство по установке

Результаты поиска

Содержание Gas/HSI & Steam ID-120

Отзывы:

Похожие инструкции для Gas/HSI & Steam ID-120

Бренды по названию

Популярные бренды