American Dryer Corp. Gas/HSI & Steam ID-120 Скачать руководство пользователя

Страница: 33 / 54

4. Steam Damper Air System Connections

This dryer is manufactured with a pneumatic (piston) damper system, which requires an external supply of

compressed air of 0.75 CFH. The air connection is made to the steam damper solenoid valve, which is

located at the rear of the top console.

a. Air Requirements

b. Air Connection

Air connection to system --- 1/8 F.P.T.

c. No air regulator or filtration is provided with the dryer. External regulation/filtration of 80 PSI (5.51

bars)

must be

provided. It is suggested that a regulator/filter gauge arrangement be added to the

compressed air line just before the dryer connection. This is necessary to insure that correct and clean

air pressure is achieved.

5. Steam Damper System Operation

The steam damper, as shown in the

top illustration

(

Diagram 1

) on

page 30

, allows the coil to stay

constantly charged eliminating repeated expansion and contraction. When the damper is opened, the air

immediately passes through the already hot coil, providing instant heat to start the drying process. When

the damper is closed, ambient air is drawn directly into the basket (tumbler), allowing a rapid cool down.

Diagram 1

shows the damper in the heating (open) mode, allowing heat into the basket (tumbler).

Diagram 2

shows the damper in the cool down (closed) mode, pulling ambient air directly into the basket

(tumbler) without passing through the coils.

NOTE:

With the dryer off or with no air supply, the steam damper is in cool down mode as shown in

Diagram 2

(refer to the

illustration

on the following page).

COM P RESSED

AIR SUP PLY

AIR P RESSURE

Normal

80 PSI

5.51 bars

Minimum Supply

70 PSI

4.82 bars

Maximum Supply

90 PSI

6.21 bars

Shaded areas are stated in metric equivalents

Содержание Gas/HSI & Steam ID-120























































Результаты поиска

Содержание Gas/HSI & Steam ID-120

Отзывы:

Похожие инструкции для Gas/HSI & Steam ID-120

Бренды по названию

Популярные бренды

American Dryer Corp. Gas/HSI & Steam ID-120, Руководство по установке

Результаты поиска

Содержание Gas/HSI & Steam ID-120

Отзывы:

Похожие инструкции для Gas/HSI & Steam ID-120

Бренды по названию

Популярные бренды