American Dryer Corp. ADG-530D II Скачать руководство пользователя | Manualshive

Страница: 49 / 57

background image

45

Possible reasons for overheating...

1. Restriction in location exhaust ductwork...

a. Dryer exhaust damper stuck in closed position.

b. Undersized exhaust ductwork.

2. Insufficient make-up air.

J.

Microprocessor controller (computer) will not accept any, or only accept certain keyboard (touch
pad) entries...

The “SEFL” display condition indicates a rotational sensor circuit failure, which means that there is a fault
somewhere in the basket (tumbler) rotation detection circuit...or...the microprocessor controller (computer)
program related to this circuit (

PL01

) is set incorrectly in the active mode (“SEn”) where the dryer is not

equipped with the optional rotational sensor and

should be

set in the inactive mode (“nSEn”).

If the dryer is equipped with the optional rotational sensor and for whatever reason the microprocessor controller
(computer) detects that the basket (tumbler) is not turning, it will disable

ALL

of the dryer outputs (shut the dryer

down), and the light emitting diode (L.E.D.) display will read “SEFL.” The L.E.D. display will continue to read
“SEFL” until the microprocessor controller (computer) is manually reset by closing and opening the program
switch (PS).

Possible causes...

1. Loose/slipping (out of proper adjustment) basket (tumbler) belt.

2. Broken basket (tumbler) V-belt.

3. Failed motor (refer to

Item B

and

Item E

on

page 42 and page 43

).

4. Failure in the rotational sensor circuit...

a. Failed rotational sensor.

b. Loose connection or break between the rotational sensor and the microprocessor controller (computer).

K. Microprocessor controller (computer) will not accept any, or only accept certain keyboard (touch

pad) entries...

1. Failed keyboard (touch pad) label assembly.

L.

Microprocessor controller (computer) locks up and the L.E.D. display reads erroneous
message(s) or only partial segments...

1. Transient power voltage (spikes)...disconnect power to the dryer, wait 1 minute (

NOTE

: for dryer models

with optional battery backup...disconnect battery), then reestablish power to the dryer. If problem is still
evident, proceed to

Item M2 through Item M4

.

2. Failed keyboard (touch pad) label assembly.

«
...
47
48
49
50
51
...
»

Содержание ADG-530D II


























































Отзывы:

Нет отзывов

Похожие инструкции для ADG-530D II

Бренд: Canmac Страницы: 17

Supercare PRO AC7200

Бренд: Remington Страницы: 88

Бренд: Insignia Страницы: 16

Бренд: Consort Страницы: 2

Бренд: Trisa electronics Страницы: 25

Бренд: Euro-Pro Страницы: 7

Bravetti Professional K4321B

Бренд: Euro-Pro Страницы: 16

Бренд: Jata Страницы: 20

Бренд: GEAppliances Страницы: 144

Бренд: Electrolux Страницы: 26

Бренд: Electrolux Страницы: 23

Бренд: Electrolux Страницы: 32

Бренд: Electrolux Страницы: 36

Бренд: Electrolux Страницы: 80

Бренд: Electrolux Страницы: 2

Бренд: DAN DRYER Страницы: 2

Shea Soft D4740

Бренд: Remington Страницы: 8

PROluxe You AC9800

Бренд: Remington Страницы: 120

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды