American Dryer Corp. ADG-530D II Скачать руководство пользователя

Страница: 34 / 57

H. PREPARATION FOR OPERATION

The following items

should be

checked before attempting to operate the dryer:

1. Read and follow

ALL

“

CAUTION

,” “

WARNING

,” and “

DIRECTION

” labels attached to the dryer.

2. Check incoming supply voltage to be sure that it is the same as indicated on the dryer data label located

behind the left coin control panel on the right wall (refer to

Section IX

of this manual).

3. Check to assure that the dryer is connected to the type of heat/gas indicated on the dryer data label.

4. The sail switch damper assemblies are installed and preadjusted at the factory prior to shipment. However,

each sail switch adjustment

should be

checked to assure this important safety control is functioning.

5. Check bolts, nuts, screws, terminals, and fittings for security.

6. Be sure

ALL

gas shutoff valves are in the open position.

7. Be sure

ALL

back panels (guards) and electric box covers have been replaced.

8. Check

ALL

service doors to assure that they are closed and secured in place.

9. Rotate the baskets (tumblers) by hand to be sure they move freely.

I. PREOPERATIONAL TESTS

ALL

dryers are thoroughly tested and inspected before leaving the factory. However, a preoperational test

should be

performed before the dryer is publicly used. It is possible that adjustments have changed in transit.

1. Turn on electrical power to the dryer.

a. Open

ALL

gas shutoff valves.

2. Computer System Operational

a. COIN MODELS ONLY

1) The light emitting diode (L.E.D.) display(s) will flash back and forth between “FILL” and the

amount needed to start the dryer (i.e., “25”), which means that the dryer is available and 25¢ is
required to start it.

2) Insert the proper number of coins into coin acceptor. Once the correct amount needed to start the

dryer has been inserted, the L.E.D. display will read “PUSH.”

3) Start the dryer by pressing the desired setting (i.e., LOW TEMP). The L.E.D. display will now

read selection (setting) made and the amount of time vended (i.e., “LO 10”).

Содержание ADG-530D II


























































Результаты поиска

Содержание ADG-530D II

Отзывы:

Похожие инструкции для ADG-530D II

Бренды по названию

Популярные бренды

American Dryer Corp. ADG-530D II, Руководство по установке

Результаты поиска

Содержание ADG-530D II

Отзывы:

Похожие инструкции для ADG-530D II

Бренды по названию

Популярные бренды