American Dryer Corp. ADG-530D II Скачать руководство пользователя | Manualshive

Страница: 48 / 57

background image

44

G.

The dryer does not start (for COIN MODELS ONLY)...coin(s) inserted and the light emitting
diode (L.E.D.) display continues to read “FILL” and/or “Amount To Start” (does not read
“PUSH”)...

1. Coin acceptor is not adjusted properly or is dirty with lint.

2. Failed coin acceptor switch.

3. Parameter in Program Location 01 (

PL01

) set incorrectly.

a. Bad coin program

should be

set for “bCrS” and not “bCLO.”

H. Microprocessor controller (computer) L.E.D. display reads “dSFL”...

1. L.E.D. display consistently reads “dSFL” and will not clear...

a. Microprocessor controller (computer) 1/8-Amp (Slo-Blo) fuse is blown.

b. Failed microprocessor controller (computer) temperature sensor.

c. Broken wire and/or termination in sensor harness somewhere between the sensor bracket and the

microprocessor controller (computer).

d. Failed microprocessor controller (computer).

2. L.E.D. display reads “dSFL” for a short period of time (30-seconds or less) and then returns to the normal

stop “FILL” mode...

NOTE:

Once the microprocessor controller (computer) detects a problem, it updates every
30-seconds so that if a problem was a loose connection in this circuit which corrected itself,
the “dSFL” display condition would automatically be canceled.

a. Loose wire and/or termination in sensor harness somewhere between the sensor bracket and the

microprocessor controller (computer).

b. Failed microprocessor controller (computer) temperature.

I.

Microprocessor controller (computer) L.E.D. display reads “Hot”...

The “Hot” display condition indicates a possible overheating condition. The microprocessor controller (computer)
monitors the temperature in the dryer at

ALL

times. If the microprocessor controller (computer) detects that

the temperature in the dryer has exceeded 220º F (104º C), it will disable

ALL

of the dryer outputs (shut the

dryer down), the buzzer (tone) will sound for approximately 5-seconds, and the L.E.D. display will read “Hot.”
The L.E.D. display will continue to read “Hot” until the temperature has dropped to 220º F (104º C) or lower and
the microprocessor controller (computer) is manually reset by closing and opening the program switch (PS).

«
...
46
47
48
49
50
...
»

Содержание ADG-530D II


























































Отзывы:

Нет отзывов

Похожие инструкции для ADG-530D II

Бренд: Maytag Страницы: 52

Бренд: OdorStop Страницы: 2

Бренд: John Lewis Страницы: 36

Бренд: Orbegozo Страницы: 46

Бренд: Häfele Страницы: 17

Бренд: Frymaster Страницы: 24

Бренд: Professional Series Страницы: 12

Бренд: CaterChef Страницы: 12

Бренд: Grundig Страницы: 27

Jet CXV TurboDryer

Бренд: Dri-Eaz Страницы: 11

Бренд: Verloni Страницы: 11

Бренд: Truvox Страницы: 8

Бренд: Bosch Страницы: 56

Бренд: Bosch Страницы: 36

Бренд: Bosch Страницы: 36

Бренд: Bosch Страницы: 36

Бренд: Bosch Страницы: 56

Бренд: Bosch Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды