American Dryer Corp. ADG-530D II Скачать руководство пользователя

Страница: 8 / 57

B. SAFETY PRECAUTIONS

WARNING:

For your safety, the information in this manual

must be

followed to minimize the risk of

fire or explosion or to prevent property damage, personal injury, or loss of life.

WARNING: The dryer must never be operated with any of the back guards, outer tops, or

service panels removed. PERSONAL INJURY OR FIRE COULD RESULT.

DO NOT

store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other

appliance.

2. Purchaser/user should consult the local gas supplier for proper instructions to be followed in the event the

user smells gas. The instructions

should be

posted in a prominent location.

3. WHAT TO DO IF YOU SMELL GAS...

DO NOT

try to light any appliance.

DO NOT

touch any electrical switch.

DO NOT

use any phone in your building.

d. Clear the room, building, or area of

ALL

occupants.

e. Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

f. If you

cannot

reach your gas supplier, call the fire department.

4. Installation and service

must be

performed by a qualified installer, service agency, or gas supplier.

5. Dryer(s)

must be

exhausted to the outdoors.

6. Although

ADC

produces a very versatile dryer, there are some articles that, due to fabric composition or

cleaning method,

should not

dried in it.

WARNING:

Dry only water washed fabrics.

DO NOT

dry articles spotted or washed in dry cleaning

solvents, a combustible detergent, or “all purpose” cleaner.

EXPLOSION COULD RESULT.

WARNING: DO NOT

dry rags or articles coated or contaminated with gasoline, kerosene, oil, paint,

or wax.

EXPLOSION COULD RESULT.

WARNING: DO NOT

dry mop heads. Contamination by wax or flammable solvents will create a

fire hazard.

WARNING: DO NOT

use heat for drying articles that contain plastic, foam, sponge rubber, or

similarly textured rubberlike materials. Drying in a heated basket (tumbler) may damage
plastics or rubber and may be a fire hazard.

Содержание ADG-530D II


























































Результаты поиска

Содержание ADG-530D II

Отзывы:

Похожие инструкции для ADG-530D II

Бренды по названию

Популярные бренды

American Dryer Corp. ADG-530D II, Руководство по установке

Результаты поиска

Содержание ADG-530D II

Отзывы:

Похожие инструкции для ADG-530D II

Бренды по названию

Популярные бренды