background image

 

                     

3

 

Specifications 

 

Operating voltage 

10% to -15% 

Power consumption                  Controller only:   10W 

 

         

Operating temperature 

32 - 130 degrees Fahrenheit 

Interface to hoppers 

24VDC & 12VDC, 1.5 amps max. 

Interface to validators 

120VAC, .5 amps max. 

Hopper coin capacity 

100/hopper minimum to 2,800/hopper    
maximum (5,600 total) 

 

Warranty Information

 

 

A Return Material Authorization number (RMA #) must be obtained 

before returning a unit for repair.  A copy of invoices must 

accompany any and all warranty work.

 

 

It is the end users’ responsibility to follow cleaning and maintenance 

procedures as outlined in the validator manual. 

Any unit returned for repair requiring only a cleaning will be charged 

a flat rate plus shipping and handling. 

 

 

Validators 

Validators are warranted for two years from date of purchase. 

 
 

Hopper(s) and/or Dispenser(s) and Logic Board 

These items are warranted for one year from date of purchase. 

 
 

COVERED 

• 

Manufacturers’ defects in workmanship or materials 

 
 

NOT COVERED 

• 

Damage caused by shipping or physical abuse 

• 

Misapplication 

• 

Vandalism 

• 

End users’ attempt, on their own, to repair components 

• 

Cleaning and maintenance 

• 

Power surges and lightning strikes 

Содержание AC2002


























Отзывы: