manualshive.com logo in svg

AMD Am186 ES, Руководство пользователя, Страница: 96 / 192

Поделиться
Скачать
AMD Am186 ES Скачать руководство пользователя страница 96

Interrupt Control Unit

7-8

7.1.4.8

ESC Opcode Exception (Interrupt Type 07h)

Generated if execution of ESC opcodes (D8h–DFh) is attempted. The microcontrollers do 
not check the escape opcode trap bit. The return address of this exception points to the 
ESC instruction that caused the exception. If a segment override prefix preceded the ESC 
instruction, the return address points to the segment override prefix.

Note: All numeric coprocessor opcodes cause a trap. The Am186ES and Am188ES 
microcontrollers do not support the numeric coprocessor interface.

7.1.5

Interrupt Acknowledge

Interrupts can be acknowledged in two different ways—the internal interrupt controller can 
provide the interrupt type or an external interrupt controller can provide the interrupt type. 
The processor requires the interrupt type as an index into the interrupt vector table.

When the internal interrupt controller is supplying the interrupt type, no interrupt 
acknowledge bus cycles are generated. The only external indication that an interrupt is 
being serviced is the processor reading the interrupt vector table.

When an external interrupt controller is supplying the interrupt type, the processor 
generates two interrupt acknowledge bus cycles (see Figure 7-1). The interrupt type is 
written to the AD7–AD0 lines by the external interrupt controller during the second bus cycle.

Interrupt acknowledge bus cycles have the following characteristics:

n

The two interrupt acknowledge cycles are locked.

n

Two idle states are always inserted between the two interrupt acknowledge cycles.

n

Wait states are inserted if READY is not returned to the processor.

Figure 7-1

External Interrupt Acknowledge Bus Cycles

Notes:

1. ALE is active for each INTA cycle.

2. RD is inactive.

T1

T2

T3

T4

T1

T2

T3

T4

S0–S2

INTA

Internal lock

Ti

Ti

Interrupt

Acknowledge

Interrupt

Acknowledge

AD7–AD0

Interrupt

Type

Содержание Am186 ES

































































































































































































Отзывы:

Нет отзывов