manualshive.com logo in svg

AMD Am186 ES, Руководство пользователя, Страница: 90 / 192

Поделиться
Скачать
AMD Am186 ES Скачать руководство пользователя страница 90

Interrupt Control Unit

7-2

Software exceptions, internal peripherals, and non-cascaded external interrupts supply the 
interrupt type through the internal interrupt controller.

Cascaded external interrupts and slave-mode external interrupts get the interrupt type from 
the external interrupt controller by means of interrupt acknowledge cycles on the bus.

7.1.1.2

Interrupt Vector Table

The interrupt vector table is a memory area of 1 Kbyte beginning at address 00000h that 
contains up to 256 four-byte address pointers containing the address for the interrupt service 
routine for each possible interrupt type. For each interrupt, an 8-bit interrupt type identifies 
the appropriate interrupt vector table entry.

Interrupts 00h to 1Fh are reserved. See Table 7-1.

The processor calculates the index to the interrupt vector table by shifting the interrupt type 
left two bits (multiplying by 4).

7.1.1.3

Maskable and Nonmaskable Interrupts

Interrupt types 08h through 1Fh are maskable. Of these, only 08h through 14h are actually 
in use (see Table 7-1). The maskable interrupts are enabled and disabled by the interrupt 
enable flag (IF) in the processor status flags, but the INT command can execute any interrupt 
regardless of the setting of IF.

Interrupt types 00h through 07h and all software interrupts (the INT instruction) are 
nonmaskable. The nonmaskable interrupts are not affected by the setting of the IF flag.

The Am186ES and Am188ES microcontrollers provide two methods for masking and 
unmasking the maskable interrupt sources. Each interrupt source has an interrupt control 
register that contains a mask bit specific to that interrupt. In addition, the interrupt mask 
register is provided as a single source to access all of the mask bits.

If the interrupt mask register is written while interrupts are enabled, it is possible that an 
interrupt could occur while the register is in an undefined state. This can cause interrupts 
to be accepted even though they were masked both before and after the write to the interrupt 
mask register. Therefore, the interrupt mask register should only be written when interrupts 
are disabled. Mask bits in the individual interrupt control registers can be written while 
interrupts are enabled, and there will be no erroneous interrupt operation.

7.1.1.4

Interrupt Enable Flag (IF)

The interrupt enable flag (IF) is part of the processor status flags (see Section 2.1.1 on 
page 2-2). If IF is set to 1, maskable interrupts are enabled and can cause processor 
interrupts. (Individual maskable interrupts can still be disabled by means of the mask bit in 
each control register.)

If IF is set to 0, all maskable interrupts are disabled.

The IF flag does not affect the NMI or software exception interrupts (interrupt types 00h to 
07h), and it does not affect the execution of any interrupt through the INT instruction.

7.1.1.5

Interrupt Mask Bit

Each of the interrupt control registers for the maskable interrupts contains a mask bit (MSK). 
If MSK is set to 1 for a particular interrupt, that interrupt is disabled regardless of the IF 
setting.

Содержание Am186 ES

































































































































































































Отзывы:

Нет отзывов