manualshive.com logo in svg

AMD Am186 ES, Руководство пользователя, Страница: 110 / 192

Поделиться
Скачать
AMD Am186 ES Скачать руководство пользователя страница 110

Interrupt Control Unit

7-22

7.3.8

Interrupt In-Service Register
(INSERV, Offset 2Ch)
(Master Mode)

The bits in the In-Service register are set by the interrupt controller when the interrupt is 
taken. Each bit in the register is cleared by writing the corresponding interrupt type to the 
End-of-Interrupt (EOI) register.

Figure 7-11

Interrupt In-Service Register

The INSERV register is set to 0000h on reset.

Bits 15–11: Reserved

Bit 10: Serial Port 0 Interrupt In-Service (SP0)—This bit indicates the in-service state of 
serial port 0.

Bit 9: Serial Port 1 Interrupt In-Service (SP1)—This bit indicates the in-service state of 
the serial port 1.

Bits 8–4: Interrupt In-Service (INT4–INT0)—These bits indicate the in-service state of 
the corresponding INT pin.

Bit 3: DMA Channel 1/Interrupt 6 In-Service (D1/I6)—This bit indicates the in-service 
state of DMA channel 1 or INT6.

Bit 2: DMA Channel 0/Interrupt 5 In-Service (D0/I5)—This bit indicates the in-service 
state of DMA channel 0 or INT5.

Bit 1: Reserved

Bit 0: Timer Interrupt In-Service (TMR)—This bit indicates the state of the in-service timer 
interrupts. This bit is the logical OR of all the timer interrupt requests. When set to a 1, this 
bit indicates that the corresponding timer interrupt request is in-service.

15

7

0

Reserved

Res

TMR

D0/I5

D1/I6

I0

I1

I2

I3

I4

SP1

SP0

Содержание Am186 ES

































































































































































































Отзывы:

Нет отзывов