manualshive.com logo in svg

Amazone FTender 1600, Оригинальное руководство по эксплуатации

Поделиться
Скачать
Amazone FTender 1600 Скачать руководство пользователя страница 59

6.3.2 Configuring the hydraulically actuated working position sensor

The pointer 

4

 shows whether the metering units

are activated. If the pointer is positioned above the 1

1

, the metering units are activated. If the hydraulic

tractor control unit is actuated, the pointer swivels

over the 0 

3

. The working position sensor 

2

deactivates the metering units.

4

1

3

2

CMS-I-00002530

To actuate the working position sensor,

actuate the "yellow" tractor control unit.

or

To switch the working position sensor via
headland management,

refer to the "tractor" operating manual.

6.3.3 Moving the T-Pack F into working position

1.

Lower the implement.

2.

Remove the linch pin 

1

.

3.

Open the locking mechanism 

2

.

CMS-I-00002478

CMS-T-00005823-A.1

CMS-T-00003211-B.1

6 | Preparing the machine

Preparing the implement for operation 

MG6492-EN-II | G.1 | 26.04.2021

53

Содержание FTender 1600











































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды