manualshive.com logo in svg

Amazone FTender 1600, Оригинальное руководство по эксплуатации

Поделиться
Скачать
Amazone FTender 1600 Скачать руководство пользователя страница 40

4.8.3 Hopper interior lighting

The hopper interior lighting is used for better a
view inside the fertiliser hopper. The hopper interior
lighting is switched on with the lighting for road travel.

CMS-I-00002219

4.9 Compressed air fan

The compressed air fan 

1

 produces an air current

that carries the metered material to the seed drill.
The fan is driven by a hydraulic motor. The fan

guard screen 

2

 protects the user against injuries

caused by rotating parts and the fan against foreign

objects. The overpressure in the conveyor section 

3

provides information on the strength of the air current.

1

2

3

CMS-I-00002467

4.10 Cyclone separator

The cyclone separator 

1

 protects the fan and the

implement under very dusty working conditions. The

intake air 

3

 is rotated so strongly in the cyclone

separator that the impurities are carried to the outer

wall and escape through the opening 

2

.

CMS-I-00002764

CMS-T-00001987-A.1

CMS-T-00003152-B.1

CMS-T-00005099-A.1

4 | Product description

Compressed air fan 

MG6492-EN-II | G.1 | 26.04.2021

34

Содержание FTender 1600











































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды