manualshive.com logo in svg

AMATI 25076, Руководство пользователя

Поделиться
Скачать
AMATI 25076 Скачать руководство пользователя страница 53

Bismarck

205

1172

1167 

Take the sheet with the transfers of the Sound Locator System that you will have 

to apply to the sides of the hull of the model. Cut out one of the two decals provided 

with the SLS, leaving a little margin around the drawing. Immerse the first transfer in 

a tray of water. 

1172 

Using fine-grit sandpaper, remove the black and red paint from the parts in relief 

on the plate. The engraved graphics will keep the two colours. Finally, glue the plate to 

the centre of the inclined wall of the wooden support with superglue.  

1169 

Take wooden support 8039 and brass plate 1601 which you can find on sheet 

1563. 

1171 

Take sheet 1601 and paint the profile of the ship in matt black and the central 

writings engraved on the plate masking the “Amati” logo at the bottom right. Once 

dry, remove the adhesive tape and vice versa paint the logo in Ral 3003 red, masking 

the rest of the plate. Let it dry very well and remove the tape from the plate. 

1168 

Mark the measurement of 186mm on the starboard side of the hull, starting 

from the bow of the ship, and the measurement of 16mm starting from the lower 

profile of the hull. Take the wet transfer and slide the drawing across the hull surface 

aligned with the traced marks. Spread it with a brush and let it adhere well to the 

surface. Repeat the same operation for the port side.

1170 

With medium-grit sandpaper, sand the entire surface of the wooden support. 

Apply a nut-brown stain of sufficient quantity, until you reach the shade you desire. 

Once dry, sand again with fine-grit sandpaper. Finally, to enhance the wood, spread 

the beeswax on the support. 

1167

1170

1168

1171

1169

BOW

1601

1601

1601

8039

8039

186mm

16mm

Содержание 25076

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды