AMATI 25076 Скачать руководство пользователя страница 34

Страница: 34 / 56

Bismarck

138

716

Glue the ladder to cylinder 2455 vertically against the flange. Bend and glue

the right end of drainage pipe 1203 around the turret to below the flange (see detail

above); the other end instead curves to the left above the ladder and also ends under

the flange. On the left side of ladder 1201, glue aerator 2457 and hatch 1202 with the

hinges oriented to the left. Align these two elements with the bottom edge of ladder

1201. Finally glue railing 1204 along the edge of the flange.

721-722

Rotate the structure and glue wall 1210 on the other linear side of the plat-

form. Align the railing with the two sides; the wall will protrude under the platform.

With flat nose pliers, bend along the engraved marks the frame of piece 1211 as

shown in detail. Fix the frame to the centre of the railing in the joints of wall 1210.

718

Model cable 1205 and glue it to the cylinder of turret 2455 aligned with the cable

in relief on the side walls. Place the cable's electrical panel in the centre.

720

Using the cylindrical template P2, model the two railings 1208. Check that the

curve follows the rounded profile of the platform; then glue the two railings 1208 to

the semicircular ends of the platform and railing 1209 on the linear side. Place the

thicker edge of the railings against the profile of platform 197.

717

Try to insert without gluing turret 2455 in the rear semicircular opening of the

stern superstructure; point ladder 1201 to the port side.

719

Take the platform of searchlight deck 197 (step 711) and all its accessories, which

you can find on sheet 1559 shown in the picture.

721

722

716

719

717

720

718

2457

1208

1210

1211

1209

1210

1208

1209

1208

1209

1210

1211

197

1213

1214

1212

1214

1208

1202

1201

1203

2455

1204

1205

1201

2455

BOW

Содержание 25076

























































Результаты поиска

Содержание 25076

Отзывы:

Бренды по названию

Популярные бренды

AMATI 25076, Руководство пользователя

Результаты поиска

Содержание 25076

Отзывы:

Бренды по названию

Популярные бренды