AMATI 25076 Скачать руководство пользователя страница 25

Страница: 25 / 56

Bismarck

414

Prepare the accessories shown in the picture, which you can find on sheet 1557;

they will be used to set up the walls of the tower. Arrange the two profiles 825 and

826 with the end without the tooth (see detail) facing the port side of the structure.

419

Continue along the rounded edge of the tower wall and cover with profile 829

up to railing 822.

416

Glue the two profiles 825 and 826 at regular heights along the rear wall of the

tower. The missing tooth on profile 825 receives ladder 823.

418

Glue profile 827 aligned with railing 807 of the gangway, bend and glue profile

828 so that it follows the inclined edge of the tower wall as shown in the picture.

415

Glue ladder 823 and profile 824 on the left wall of the tower as shown in the

picture. Model profile 824 first according to the curve of the tower.

417

The picture shows the view of the two profiles 825 and 826 on the other side of

the tower. Prepare the other pieces 827, 828, 829 (sheet 1557) to continue with the

preparation.

419

414

417

415

418

416

822

823

824

826

825

826

825

826

823

827

828

807

827

829

822

Содержание 25076

























































Результаты поиска

Содержание 25076

Отзывы:

Бренды по названию

Популярные бренды

AMATI 25076, Руководство пользователя

Результаты поиска

Содержание 25076

Отзывы:

Бренды по названию

Популярные бренды