AMATI 25076 Скачать руководство пользователя страница 4

Страница: 4 / 56

Bismarck

009

011

007

010

008

012

010

Try inserting keel 2 in the bow joint of keel 1; then glue with wood glue.

012

Move forward and try assembling bulkheads 18, 17, 16, 15 in the joints of keel

2. Check that they are perpendicular to the keel and parallel to each other; then glue.

011

Take support 7 and place it on the joint of keel 1-2 against bulkhead 19. Check

its positioning and glue.

007

Remove from laser sheets 3550 and 3551 bulkheads 20, 24, 25, 26 and lay them

on your worktop together with bulkheads 19 and 23, which you have prepared in the

previous steps.

009

Move to the bow of the model and lay on your worktop keel 2, support 7 and

bulkheads 18, 17, 16 and 15 which you can find on laser sheets 3550, 3551 and 3552.

008

While performing tests without glue, insert the bulkheads in the respective joints

on keel 1. Check that they are perpendicular to the keel and parallel to each other;

then glue. Warning! Supports 19a of bulkhead 19 must point towards the bow (see

detail), while supports 23a of bulkhead 23 must point towards the stern.

23a

BOW

19a

BOW

Содержание 25076

























































Результаты поиска

Содержание 25076

Отзывы:

AMATI 25076, Руководство пользователя, Страница: 4 / 56

Результаты поиска

Содержание 25076

Отзывы: