AMATI 25076 Скачать руководство пользователя страница 48

Страница: 48 / 56

Bismarck

176

987

Remove from sprues P19, P20 the plastic components for assembling the Arado: fuselage

2584; two floats 2585, wings 2586, 2587, motor 2588, rudder 2589.

992

Insert in the holes of floats 2585 the dowels of the support diagonals 1478, 1479;

check that they are parallel to each other; then glue.

989

With a fine drill bit, go over the holes indicated by the red arrows:

under fuselage 2584, on floats 2585 and on wings 2586, 2587.

991

Remove the sled and insert two supports 1478, 1479 into the four front dowels

under the fuselage. Orient the wings of piece 1479 towards the nose, those of piece

1478 towards the tail; then glue them in place.

988

Take the support diagonals of floats 1478, 1477 which you can find on sheet

1564 and bend the side flaps of the two supports upwards. With a fine drill bit, go

over the three holes on motor 2588 for assembling propeller blades 1479 which you

can find on sheet 1564. Insert them diagonally into the holes as shown in the detail

above; then glue.

990

Temporarily insert the dowels of the sled structure of the catapult prepared in

step 986 into the three lower holes of fuselage 2584, orient the pieces correctly and

do not glue.

992

987

990

988

991

989

do not glue

1477

2584

2585

2589

2587

2586

2588

2585

1479

1474

2584

1479

2588

1479

1478

1479

1478

2589

2585

2584

2587

2586

2588

1479

1474

Содержание 25076

























































Результаты поиска

Содержание 25076

Отзывы:

AMATI 25076, Руководство пользователя, Страница: 48 / 56

Результаты поиска

Содержание 25076

Отзывы: