AMATI 25076 Скачать руководство пользователя страница 52

Страница: 52 / 56

Bismarck

180

1015

Paint with a brush launch 2596, following the colours and measurements shown

in the pictures above. Colour the hull, railings and handrails in Ral 7001 grey; the hull

below the waterline in Ral 8013 red; the upper part of the motor boat in Ral 8016

mahogany brown; the benches in Ral 1001 light wood and the ring buoy 1493 (x2)

in matt white. Once dry, you can glue canopy 1504 on the superstructure. Repeat the

assembly of the lifeboat and prepare a total of two motor boats.

1010

With the pieces shown in the picture (sheet 1564) set up the second type of

boat: motor launch 2595, frame (P8). Referring to the following pictures, slightly curve

windshield 1487 and canopy 1491 in view of their positioning.

1012

Paint with a brush motor launch 2595, following the colours and measurements

shown in the pictures above. Colour the hull and the rails in Ral 7001 grey; the hull

below the waterline in Ral 8013; the upper part of the lifeboat in Ral 8016 mahogany

brown and ring buoy 1493 (x2) in matt white. Once dry, you can glue canopy 1491

onto the superstructure.

1014

Before gluing the various accessories on the launch, widen the holes intended

for fitting the handrails, railings and propeller shaft. Then glue the accessories in place

on the lifeboat. Set up canopy 1504 with ring buoys 1493 (x2) and the two handrails

1505. Also attach rudder 1488 and lever 1500, as shown in the detail.

1011

Glue the two handrails 1486, windshield 1487, ship’s wheel 1488 on launch

2595, as shown in the picture. With a fine drill bit, go over the two holes under the

hull for propeller shaft 1489. Insert and glue propeller 1490 to shaft 1489; if necessary,

enlarge the hole in the centre of the propeller. Glue the shaft and propeller to the hull

as shown in the detail above. Couple the two ring buoys 1493 together and set up

canopy 1491 with the two 1492 handrails and ring buoys 1493 (x2).

1013

Now prepare the third type of boat: officer’s launch. Prepare the accessories

presented in the picture above which you can find on sheet 1564 and plastic launch

2596, frame P10. Referring to the following pictures, slightly curve windshield 1497,

railings 1496, 1499 and canopy 1504.

1015

1010

1013

1011

1014

1012

2595

2596

2595

1486

1487

1488

1489

1490

1486

1492

1490

1489

1491

1492

1488

1487

1493

1495

1496

1497

1498

1500

1488

1500

1501

1504

1505

1504

1505

1493

1505

1502

1499

1493 (x2)

1491

1492

2595

2596

1504

2595

MOTOR BOAT

MOTOR LIFEBOAT

3mm

Содержание 25076

























































Результаты поиска

Содержание 25076

Отзывы:

Бренды по названию

Популярные бренды

AMATI 25076, Руководство пользователя

Результаты поиска

Содержание 25076

Отзывы:

Бренды по названию

Популярные бренды