AMATI 25076 Скачать руководство пользователя страница 46

Страница: 46 / 56

Bismarck

174

2553

974

With the next assembly steps you will have to prepare the 10.5 cm. front

heavy anti-aircraft guns (2581a, 2582 frames P14, P15) and the 10.5 cm rear

heavy anti-aircraft guns (2581b, 2583 frames P16, P17) which will be fixed on the

decks of the superstructures. To start, drill two holes at the bases of each carriage

for the insertion of barrels 20/02 as shown in the detail.

980

Then move to the stern superstructure and fix the other four bases 2553 (P25) to

the lower deck aligned with the holes drilled in step 794 of these assembly instruc-

tions.

976

Insert the barrels in the pair of holes of each cannon,

fix them with the glue in a parallel position. You will have

to prepare a total of eight cannons: four front 2582 and

four rear 2583; therefore replicate the assembly from step

974 to step 976 and assemble eight cannons in total.

977

Now you can colour the entire surface of the

eight cannons with Ral 7001 paint. Let the rods and

the upper part of the caps dry well and brush with Ral

7024 paint, following the colouring areas shown in

the picture above and in the following one.

979

Detach the eight circular bases 2553 for the heavy anti-aircraft guns from sprue P25.

Fix four to the lower deck of the bow superstructure in correspondence with the four holes

drilled in steps 309, 311 of the first instructions manual.

975

Join caps 2582 and 2583 to the respective bases 2581a

and 2581b; then glue.

978

The picture shows the colouring areas of the cannons seen from another

angle. Temporarily keep the eight newly assembled and painted cannons aside.

980

974

978

975

979

976

977

2583

2582

2581b

20/02

2581a

2582

hole

Ø 1.1mm

Содержание 25076

























































Результаты поиска

Содержание 25076

Отзывы:

Бренды по названию

Популярные бренды

AMATI 25076, Руководство пользователя

Результаты поиска

Содержание 25076

Отзывы:

Бренды по названию

Популярные бренды