AMATI 25076 Скачать руководство пользователя страница 22

Страница: 22 / 56

Bismarck

396

Then glue deck 2346 to the tower oriented as shown in the picture above.

401

Glue the railings on the external profile of platform 803 in the position shown in

the picture and prepare the other pieces from 808 to 811. Lift the ends of pieces 808

(x2), 811 and 810 upwards as shown in the picture.

398

Move to the front wall of the tower and glue door 799 and hatch 800 in the

position shown.

400

Now prepare the platform with gangway 803, with the railings from 804 to 807

which you can find on sheet 1557 and which once completed will be glued to the

tower. Raise the ends of railings 807 (x2) and gangway 803 to 90°.

397

Now remove the seven doors from 796 to 802 from sheet 1557, which will be

glued to the tower. Glue doors 796, 797, 798 to the points indicated in the picture,

taking care not to confuse the pieces.

399

Proceed in the same way with doors 801 and 802. The photo also shows door

798 glued in step 397.

396

399

397

400

398

401

2346

796

797

799

801

802

798

803

804

811

810

806

805

807

809

808

809

799

798

800

BOW

Содержание 25076

























































Результаты поиска

Содержание 25076

Отзывы:

Бренды по названию

Популярные бренды

AMATI 25076, Руководство пользователя

Результаты поиска

Содержание 25076

Отзывы:

Бренды по названию

Популярные бренды