Amano AGP-2000 Series Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 40

Amano AGP-2000 Series Скачать руководство пользователя страница 33

To recover from a restocking misfeed:

If the tickets misfeed after restocking or while switching to a new box (dual ticket feed)
the display will indicate the following:

The character F or B will appear in the first position of the date/time display. If an F
appears, the misfeed has occurred in the Front, or Dual Ticket Feed opening of the
transport. If a B appears, the misfeed has occurred in the Back or rear opening of the
transport. To recover from the misfeed, perform the following procedure:

1. Make sure Loop A is clear.
2. Open the side door panel if you have not already done so.
3. Tear off the tickets from all ticket boxes.
4. Press and release the Ticket Issue button.
5. All motors in the RWPV will run until all the sensors are clear. Any tickets

remaining in the RWPV will be ejected. Remove any rejected tickets.

Note:

All RWPV motors will stop if the Ticket Issue button is pressed a second time.

The display will show a TICKET JAM if the tickets are not removed. You may remove
the tickets by hand if needed. (Refer to the previous section.)

6. The AGP-2000 will show an OPEN status unless it has been CLOSED due to

another command.

7. Restock the tickets as described previously.
8. Close and lock the door.

Closed

F10/17/99

09:39A

AGP-2000 Installations and Operations / SERVICE

4 - 5

«
...
31
32
33
34
35
...
»

Содержание AGP-2000 Series









































Отзывы:

Нет отзывов