manualshive.com logo in svg

Amano AGP-2000 Series, Руководство по установке и эксплуатации, Страница: 31 / 40

Поделиться
Скачать
Amano AGP-2000 Series Скачать руководство пользователя страница 31

Ticket Jam

If a ticket should become jammed in the ticket transport, the display will indicate 
the following:

To clear the ticket jam, perform the following procedure:

1. Open the side door panel if you have not already done so. 
2. Press and release the Door Open switch to reset the ticket jam. Press and hold

the Door Open switch down again and observe the display. If the display does
not return to normal, proceed as follows:

3. Locate the jammed ticket within the ticket transport.  
4. Refer to Figure 4-3 below to locate the Printer Release Latches 

on both

sides of the printer. Pull both of the latches forward to release the printer.

5. Tilt the printer assembly up and back 

.

6. Locate the pulleys on the left side of the upper mechanism 

.

Rotate each set of motor driven pulleys to move the ticket towards the front or
rear of the mechanism. 

7. Grasp the jammed ticket and remove it from the mechanism. 
8. Tilt the printer assembly back down and reset the latches.
9. Press and release the Door Open switch to reset the ticket jam.

10. Close and latch the top cover.
11. Close and lock the door panel.

TICKET JAM

10/17/99

06:39A

AGP-2000 Installations and Operations / SERVICE

4 - 3

Figure 4-3, Clearing a Jammed Ticket

Содержание AGP-2000 Series









































Отзывы:

Нет отзывов