manualshive.com logo in svg

Amano AGP-2000 Series, Руководство по установке и эксплуатации, Страница: 16 / 40

Поделиться
Скачать
Amano AGP-2000 Series Скачать руководство пользователя страница 16

Mounting the AGP-2000

Follow the instructions outlined below to mount the AGP-2000 Ticket Dispenser.
Check the location of the installed conduits and anchor bolts against the bolt layout
drawing below. Make sure the conduits extend more than 1” (2.5 cm) high but do not
extend more than 2” (5 cm) high. Conduits over 2” (5 cm) high will cause damage to
components inside the Ticket Dispenser pedestal.

Two additional sets of mounting holes are provided so the AGP-2000 can replace
other ticket dispensers without changing existing mounting bolts. The AGP-2000
directly replaces the ETP-10/20, ETP-12/22 and also CTP models if a galvanized
base was previously used. 

To mount the AGP-2000 in place:

1. Make sure the power source to the field wiring is disconnected.
2. Make sure the installed field wiring is located so that it won’t be pinched when

mounting the AGP-2000.

3. Mount the AGP-2000 pedestal to the mounting bolts using the four ½ -13 nuts

removed and set aside earlier. Make sure the AGP-2000 is mounted so that the
front of the unit faces the traffic lane.

4. Make sure the MAIN POWER circuit breaker in the unit is turned OFF.
5. Proceed to make wiring connections as described on the following pages.

3 - 2

AGP-2000 Installation and Operations / INSTALLATION

Figure 3-1, Bolt Layout

Содержание AGP-2000 Series









































Отзывы:

Нет отзывов