Altendorf WA 6 Скачать руководство пользователя страница 70

Страница: 70 / 76

Faults/problems/troubleshooting

0000010064-007- GB

Workpiece jammed.

Insert a riving knife in the cutting line or use a wider riving

knife.

Operating error

Guide the workpiece either at the LH or the RH fence. Do

not guide the workpiece on the rip fence when cutting with

the sliding table.

Workpiece has

burn marks.

Blunt saw blade

Change the saw blade.

Feed too low

Increase the feed rate.

Saw blade has too

many teeth.

Change the saw blade.

Incorrect free cut

Readjust the free cut.

Break-outs in spite

of scorer

Scorer not aligned

with main saw blade

Readjust free cuts; the free cut should be almost “0”.

Scoring blade too nar

row

Adjust saw width.

Workpiece rises

when cut with the

scorer.

Blunt scoring blade

Exchange the sawing blade.

Cutting height too low

Set the scoring blade higher.

Fault

Cause

Troubleshooting

Содержание WA 6













































































Результаты поиска

Содержание WA 6

Отзывы:

Бренды по названию

Популярные бренды

Altendorf WA 6, Руководство по эксплуатации

Результаты поиска

Содержание WA 6

Отзывы:

Бренды по названию

Популярные бренды