Altendorf WA 6 Скачать руководство пользователя страница 55

Страница: 55 / 76

Operating

0000010064-007- GB

Operating

•

Switch off the drives.

•

Set the saw blade to the max. saw blade overhang and
tilt to 0°

•

Turn off the main switch

•

Move the top carriage to the middle of the saw shaft, and
unlock the lock at the saw blade centre by pressing the
knob on the middle carriage.

•

Move the top carriage to the end position in the cutting
direction.

•

Fold down the cover plate (1)

•

Push the holding mandrel (2) through the table top and
saw shaft

•

Unscrew the nut (3)

•

Before fitting the new saw blade, remove any adhering
chips and dust from both flanges

•

Place the saw blade and front flange on the saw shaft,
screw in by hand and tighten nut

•

Check the riving knife (4) for thickness and distance from
the saw blade

•

If these factors are not OK:
• Undo the screw (5)
• Adjust or replace the riving knife
• Tighten the screw

•

Remove the holding mandrel

•

Close the cover plate and perform a brief trial run to
check whether the saw blade operates without problems
(during this process, lower the top protective hood all the
way down to the table so that the saw blade is fully cov

ered)

WARNING!

Check that saw blade clamping system is tight before operating the machine!

Содержание WA 6













































































Результаты поиска

Содержание WA 6

Отзывы:

Бренды по названию

Популярные бренды

Altendorf WA 6, Руководство по эксплуатации

Результаты поиска

Содержание WA 6

Отзывы:

Бренды по названию

Популярные бренды