manualshive.com logo in svg

Altendorf WA 6, Руководство по эксплуатации

Поделиться
Скачать
Altendorf WA 6 Скачать руководство пользователя страница 38

Installation

38

Installation

0000010064-007- GB

6.3.9

Groove tools

The groove tools require a hole diameter of 30 mm and carrier holes of 10 mm 
Ø on a pitch circle diameter of 60 mm Ø. Loose intermediate rings may not be 
used. The maximum groove width is 20 mm and the maximum hub width is 15 
mm. A groove tool of 180 mm Ø results in a maximum overhang of 36 mm.

•

Switch off the drives.

•

Set the saw blade to the max. saw blade overhang and 
tilt to 0°

•

Turn off the main switch

•

Move the top carriage to the middle of the saw shaft, and 
unlock the lock at the saw blade centre by pressing the 
knob on the middle carriage.

•

Move the top carriage to the end position in the cutting 
direction.

•

Fold down the cover plate (1)

•

Undo the screw (2)

•

Remove the riving knife (3) and protective hood (4)

•

Pull the riving knife holder left and tighten the screw (2)

•

Push the holding mandrel (5) through the table top and 
saw shaft

•

Unscrew the nut (6)

•

Remove the saw blade and front cushioning disc (7)

•

Undo the screws (8) of the front table strip and then 
remove the front table strip (9)

•

Before fitting the new groove tool, remove any adhering 
chips and dust from both flanges

•

If necessary, use a cushioning disc based on the groove 
tool 

•

Place the groove tool and front flange on the saw shaft, 
screw in by hand and tighten nut (3)

•

Close the protective cover, move the sliding table to its 
operating position, switch on the main switch and exe

-

cute a brief trial run to check whether the groove tool 
operates without problems

WARNING!

The following points must always be observed:

Non-adherence may lead to severe injuries!

•

Do not fit any groove tools that are cracked or damaged in any way.

Содержание WA 6













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды