manualshive.com logo in svg

Altendorf WA 6, Руководство по эксплуатации

Поделиться
Скачать
Altendorf WA 6 Скачать руководство пользователя страница 29

Product description

29

0000010064-007- GB

Product description

2. Limit switch, plate, chip duct

•

Push the sliding table to its end position (centre of main 
saw)

•

The limit switch (2) is tripped when the cover plate is 
folded away

•

Actuate ON button of main and scoring saw

•

Ensure that the main and scoring saw do not start

3. Sliding table limit switch

•

Start the main and scoring saw

•

Actuate the unlocking mechanism to push the sliding 
table over the centre of the main saw (see figure), this 
trips the limit switch (3)

•

Ensure that the main and scoring saw stop within 10 sec.

4. ON and OFF switches

•

Check all ON and OFF switches (4) for soiling

•

Clean all ON and OFF switches (4) in the event of soiling

5. Protective hood

•

Check protective hood (4) for damage

•

Replace protective hood (4) if damaged

WARNING!

The safety-relevant protective devices/guards exist for the operator’s protec

-

tion. If safety-relevant components are damaged, immediately stop and secure 
the machine and initiate the required repair work. The operator must assess 
damage to non-safety-relevant components and initiate repair work accord

-

ingly.

i

Note!

Carry out and document this check 1x month!
We recommend inserting these tests in the owner/user's instructions.

i

Note!

If the run-down time of the main saw exceeds 10 sec, please contact the Alten

-

dorf customer service.

Содержание WA 6













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды