Altendorf WA 6 Скачать руководство пользователя страница 35

Страница: 35 / 76

Installation

0000010064-007- GB

Installation

6.3.7

Electrical connection

The controls of an extraction system require a floating contact. An auxiliary
contactor can be controlled using a 2-wire control line leading out. The maxi

mum control voltage / current is 240VAC / Imax=1A.

WARNING!

Dangerous electric voltage!

All work on the electrical equipment, including connection to the mains supply,
may only be performed by a qualified electrician.

Disconnect the machine from the mains supply before working on the electrical
equipment.

•

A round plug device under the sliding table is used to establish the connec

tion. Use a rubber hose line (H07RN-F), cross section 5x 2.5 mm2 as the
supply line.

•

After connecting the supply line, check the rotational direction of the main
saw motor by briefly starting up and, if necessary, correct it.

•

Pay attention to the rotational direction arrow on the saw blade cover!

•

The owner/user must provide a short-circuit protection!

•

Do not route supply lines or the potential-free contact through the support
arm.

Содержание WA 6













































































Результаты поиска

Содержание WA 6

Отзывы:

Бренды по названию

Популярные бренды

Altendorf WA 6, Руководство по эксплуатации

Результаты поиска

Содержание WA 6

Отзывы:

Бренды по названию

Популярные бренды