Altendorf WA 6 Скачать руководство пользователя страница 41

Страница: 41 / 76

Installation

0000010064-007- GB

Installation

6.4.4

Cross-slide height

6.4.5

Setting free cut

Checking the cross-slide height

•

Push an approx. 0.5 mm thick test object (e.g. card

board) in between the crosscut-mitre fence and the slid

ing table

•

The test object must slide freely at every position

Setting

•

Undo the lock nut (1) and the bottom nut (2)

•

Turn the top nut (3) clockwise or counter-clockwise,
depending on the incline

•

Tighten the bottom nut (2) and lock nut (1)

Checking the sliding table free cut

•

Set the saw blade to the maximum cutting height

•

Position a board (preferably MDF) on the crosscut-mitre
fence and cut off a narrow piece

•

When the rising teeth pass, only a slight fluttering should
be heard compared to the noise of the cutting teeth (cut

ting up)

Setting the sliding table free cut

•

Undo the screws of the support pad

•

Undo the lock nut (1)

•

Re-adjust the screw (2) accordingly, then lock with the
nut

•

Adjust the support pad so that it makes contact

•

Tighten the screws of the support pad

Содержание WA 6













































































Результаты поиска

Содержание WA 6

Отзывы:

Бренды по названию

Популярные бренды

Altendorf WA 6, Руководство по эксплуатации

Результаты поиска

Содержание WA 6

Отзывы:

Бренды по названию

Популярные бренды