Altendorf WA 6 Скачать руководство пользователя страница 52

Страница: 52 / 76

Operating

0000010064-007- GB

The drive motor is protected against overload. This overload protection auto

matically switches off the motor in the event of excessive heat generation. En

sure that the scorer drive is also switched off for machines equipped with a
scorer. The motor can only be switched on again when it has cooled down. It
may take several minutes (max. 10 min.) for the motor to cool down!

7.3

Switching the saw drives on and off

•

Switch on the main saw (1)

•

Once the saw blade has reached its full speed, switch on
the scoring saw (2)

•

Switch off the main and scoring saw (3)

WARNING!

Prior to switching on the machine:

•

ensure that all protective devices/guards are attached and have been
checked for function

•

ensure that the correct clamping of saw blades has been checked

•

remove all workpieces and objects near the saw blade

•

check the rotational direction of the saw blade by briefly switching it on

When switching on the machine:

•

ensure that the extraction system is activated

Содержание WA 6













































































Результаты поиска

Содержание WA 6

Отзывы:

Бренды по названию

Популярные бренды

Altendorf WA 6, Руководство по эксплуатации

Результаты поиска

Содержание WA 6

Отзывы:

Бренды по названию

Популярные бренды