Alpha tools A-ES 700/1, Оригинальная инструкция по эксплуатации

Страница: 16 / 236

GB
- 16 -
5. Charging the energy station
Notice! Turn the ON/OFF knob (Fig. 1/Item 10) to
the “OFF” position.
Notice! Pressing the red pushbutton (5) displays
the charge state of the built-in battery (green = 50
– 100% full / red = 0 – 50% full)
5.1 Charging the energy station with the
power supply unit
1. Connect the power cable of the included
power supply unit to the battery charging jack
(7). The LED (6) fl ashes for a moment.
2. Plug the power supply unit into a 230V/50Hz
socket outlet. Depending on the charge state
of the battery, the LED (6) will light up red
(0 - 50% full) or green (50 - 100% full). The
charging voltage switches o ff automatically
after completion of the charging process.
Overcharging of the battery is ruled out. The
green LED (6) will come on.
5.2 Charging the energy station with the
automobile adapter cable
The energy station can be charged through the
automobile’s cigarette lighter socket.
Notice! You should only charge the energy station
when en route, as otherwise the unit will run down
the vehicle’s battery.
Never start the vehicle as long as the automobile
adapter cable is connected to the cigarette lighter
socket.
Insert the 12 volt plug of the automobile adapter
cable into the automobile’s cigarette lighter so-
cket and insert the other end of the cable into the
charging jack of the energy station marked (7).
6. Outputs
Caution!
Output 12 V through the cigarette lighter plug
connection.
10 Amperes max.:
•
The 12 V output (Fig. 1 / Item 4) is designed
to handle 10 A, i.e. there are max. 10 A availa-
ble to use.
•
Observe the power/electricity consumption
values of the consumer, to prevent overloa-
ding the energy station. If only the power data
of the consumer is known, the maximum
electricity value can be easily calculated.
Example calculation:
Consumer: 12V / 50W
The electricity consumption is equal to:
50W / 12V = 4.17A
•
The cigarette lighter cable provided can be
used to connect a suitable consumer.
It is protected by a 10 A fuse.
•
In order to use the 12 V output, remove the
protective cap and connect the consumer.
Observe the voltage and electricity values
of the appliances to be used, in order not to
overload the energy station.
Overload could lead to destruction of the
appliance.
7. Using the light
To switch the light on, proceed as follows:
The light (Fig. 1 Item 2) is switched ON and OFF
with the switch (Fig.1/Item 9).
8. Jump-start for motor vehicles
Danger!
•
The charging cable with pole clips are situa-
ted on the side of the appliance.
•
If you do not need the charging cable, do not
remove this from the appliance.
•
Important. Danger of short-circuit if pole clips
are contacted.
•
The energy station can only be used to
jump-start partially discharged motor vehicle
batteries. This means you can only convey a
limited capacity into the motor vehicle battery.
•
The energy station is NOT designed to
start completely discharged batteries!
The terminals are insulated to prevent accidental
short-circuiting when connecting the terminals to
the vehicle’s battery and parts. Short-circuits must
be avoided at all costs.
If the terminals are connected to the vehicle’s
battery with reverse polarity, a warning signal will
sound and the LED (8) will light up red. Do not
activate the energy station!
If the terminals are properly connected to the
vehicle’s battery, the LED (8) will light up green.
Anl_A_ES_700_1_SPK7.indb 16 Anl_A_ES_700_1_SPK7.indb 16 23.07.14 14:22 23.07.14 14:22