Alliance Laundry Systems BWNBX2PP303AW01 Скачать руководство пользователя страница 29

Страница: 29 / 64

Slow Spin Or No Spin

Is control

inoperative?

Is lid open or lid

switch inoperative?

Test control and

replace if

inoperative.

Yes

Is there a bind in

pump?

Close lid or test

switch and replace if

inoperative.

Yes

Are there items stuck

between inner and

outer tub?

Replace pump.

Yes

Is drive belt broken

or worn?

Remove objects.

Yes

Motor won't run?

Replace belt.

Yes

Has drive motor

overload protector

cycled?

Refer to Motor Test

Procedure section to

check switch and

windings.

Yes

Is there no clearance

between brake pads

and discs?

Wait 5 to 10 minutes

for overload

protector to reset.
If protector cycles

repeatedly, refer to

Motor Does Not Run

flowchart.

Yes

Is there broken,

loose, shorted or

incorrect wiring?

Replace pads and

brake assembly.

Yes

Refer to appropriate

wiring diagram.

Yes

Troubleshooting Flowcharts

DO NOT COPY or TRANSMIT

Part No. 204591EN

Содержание BWNBX2PP303AW01

































































Результаты поиска

Содержание BWNBX2PP303AW01

Отзывы:

Похожие инструкции для BWNBX2PP303AW01

Бренды по названию

Популярные бренды

Alliance Laundry Systems BWNBX2PP303AW01, Руководство по устранению неисправностей

Результаты поиска

Содержание BWNBX2PP303AW01

Отзывы:

Похожие инструкции для BWNBX2PP303AW01

Бренды по названию

Популярные бренды