Alliance Laundry Systems BWNBX2PP303AW01 Скачать руководство пользователя страница 11

Страница: 11 / 64

General Troubleshooting

To Enter Factory Test

1. Be certain control is in Ready Mode or Start Mode and access

panel or coin vault is open.

2. While pressing and holding the NORMAL COLD modifier

keypad with one hand, press the PERM PRESS WARM key-
pad with the other hand.

3. When the control enters Factory Test, it will display the first

test step, Machine Type.

4. The control will advance through the sequence of test steps

whenever START (enter) is pressed, with the exception of the

Keypad Test and Pressure Sensor Test. Refer to the table be-
low for all tests in the Factory Test.

To Exit Factory Test

To exit a test step, disconnect the machine from electrical power.

Factory Test Cycle Quick Reference Chart

Display

Test Mode

Comments

Machine Type

Topload washer is the machine type.

S---

Software Version Number

---

is the control version number.

ob--

Output Board Version Number

is the output board software version

number.

A-

Control Level

The control will display the control type
where

is the control level.

Dip Switch Value

The control will display the status of dip
switches 1 to 8. If a dipswitch is ON, the
value shown will be 1. If the dipswitch is
OFF, the value will be 0.

PA--

Keypad Test

is the number of the keypad being

pressed. You need to press all keypads to
advance to the next step.

8.8.8.8

Display Test

All LEDs and display segments will
light.

C-C-

Coin Drop Test

is the number of coins entered. For du-

al coin drops, coin drop 1 is shown on the
left of the display and coin drop 2 is
shown on the right of the display.

Card

LCSU

Card Reader Test

Card

is displayed when a card reader is

connected but not driving the display.

LCSU

is displayed when a programming/

set-up card is needed.

is displayed

when a programming/set-up card was
successful.

Table 1

continues...

General Troubleshooting

DO NOT COPY or TRANSMIT

Part No. 204591EN

Содержание BWNBX2PP303AW01

































































Результаты поиска

Содержание BWNBX2PP303AW01

Отзывы:

Похожие инструкции для BWNBX2PP303AW01

Бренды по названию

Популярные бренды

Alliance Laundry Systems BWNBX2PP303AW01, Руководство по устранению неисправностей

Результаты поиска

Содержание BWNBX2PP303AW01

Отзывы:

Похожие инструкции для BWNBX2PP303AW01

Бренды по названию

Популярные бренды