Alliance Laundry Systems BWNBX2PP303AW01 Скачать руководство пользователя страница 35

Страница: 35 / 64

Washer Stops In Cycle, Quits After A Couple Loads, Is Intermittent

Is belt tacky, not

allowing proper slip?

Is belt tension too

great, not allowing

proper slip?

Check belt and

replace if defective.

Yes

Is control

inoperative?

Make sure idler

spring is properly

connected.

Yes

Is there broken,

loose or incorrect

wiring?

Test control and

replace if

inoperative.

Yes

Has motor overload

protector cycled?

Refer to appropriate

wiring diagram.

Yes

Are motor switch

functions inoperative?

Wait 5 to 10 minutes

for overload

protector to reset.
If protector cycles

repeatedly, refer to

Motor Does Not Run

flowchart.

Yes

Has brake,

transmission or motor

locked up and will

not turn?

Refer to Motor Test

Procedure section to

check switch

functions.

Yes

Check that all these

components are able

to move freely.

Yes

Troubleshooting Flowcharts

DO NOT COPY or TRANSMIT

Part No. 204591EN

Содержание BWNBX2PP303AW01

































































Результаты поиска

Содержание BWNBX2PP303AW01

Отзывы:

Похожие инструкции для BWNBX2PP303AW01

Бренды по названию

Популярные бренды

Alliance Laundry Systems BWNBX2PP303AW01, Руководство по устранению неисправностей

Результаты поиска

Содержание BWNBX2PP303AW01

Отзывы:

Похожие инструкции для BWNBX2PP303AW01

Бренды по названию

Популярные бренды