Alliance Laundry Systems AT120CSH Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 72

background image

M412982

39

Section 5 Service Procedures

To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the tumbler before servicing.
• Close gas shut-off valve to gas tumbler before servicing.
• Close steam valve to steam tumbler before servicing.
• Never start the tumbler with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be

reconnected to ensure that the tumbler is properly grounded.

W002

WARNING

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

51. MOTOR PULLEY

Refer to Figure 16.
a. Remove drive belt. Refer to Figure 15.
b. Loosen setscrews and remove screws from

tapered bushing.

c. Remove tapered bushing by putting the screws

removed in step “b” into the threaded holes in
the bushing. Turn the screws inward to force
the bushing out of the motor pulley.

d. Remove motor pulley.

NOTE: Realign motor pulley directly over sheave
by loosening the tapered bushing and repositioning
the motor pulley on the cylinder motor shaft.

52. JACKSHAFT ASSEMBLY

Refer to Figure 15.
a. Support drive guard cover and remove screws

that hold guard to rear of tumbler. Refer to
Figure 13.

b. Remove cylinder and drive belts.
c. Remove snap ring and pull step pulley off of

jackshaft.

d. Remove four bolts that attach jackshaft to rear

of tumbler.

NOTE: After installing sheave, adjust belts.

53. CYLINDER ASSEMBLY

a. Remove front panel assembly.
b. Support drive guard cover and remove screws

holding guard to rear of tumbler. Refer to
Figure 13.

c. Loosen the four jackshaft assembly attaching

screws. Refer to Figure 14.

d. Rotate the adjusting nuts counterclockwise

(approximately three turns).

e. Slide jackshaft assembly upwards to loosen the

cylinder belts.

f. Remove cylinder belts.

g. Remove drive belt. Refer to Figure 15.
h. Remove screws from tapered bushing. Refer to

i. Remove tapered bushing by putting the screws

removed in step “h” into the threaded holes in
the bushing. Turning the screws inward will
force the bushing out of the cylinder sheave.

j. Remove cylinder sheave.

k. Loosen setscrews on trunnion bearings. Refer

to Figure 17.

l. Pull cylinder through front of cabinet.

NOTE: When removing cylinder out through front
of cabinet, spread cabinet slightly so cylinder will
clear cabinet sides.

NOTE: After reinstalling drive and cylinder belts,
adjust belts.

Figure 16

T371PE1A

TAPERED

BUSHING

SCREWS

MOTOR

PULLEY

SETSCREW

«
...
36
37
38
39
40
...
»

Содержание AT120CSH









































































Отзывы:

Нет отзывов

Похожие инструкции для AT120CSH

Бренд: Cosori Страницы: 23

Бренд: Joycare Страницы: 56

Бренд: DCG Страницы: 28

BELLEZZA Belle Phon Professional HTD8270

Бренд: DCG Страницы: 12

Бренд: OdorStop Страницы: 2

Бренд: COMAC Страницы: 2

Бренд: Remington Страницы: 9

Бренд: aeolus Страницы: 2

Бренд: Solt Страницы: 2

Бренд: SOGEDIS Страницы: 64

Бренд: CombiSteel Страницы: 31

Бренд: baridi Страницы: 10

Бренд: FrigidaireWasher Страницы: 36

Бренд: LG Страницы: 44

Бренд: LG Страницы: 44

Бренд: LG Страницы: 48

Бренд: LG Страницы: 49

Бренд: LG Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды