Alliance Laundry Systems AT120CSH Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 72

background image

14

M412982

Section 3 Troubleshooting

To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the tumbler before servicing.
• Close gas shut-off valve to gas tumbler before servicing.
• Close steam valve to steam tumbler before servicing.
• Never start the tumbler with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be

reconnected to ensure that the tumbler is properly grounded.

W002

WARNING

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

10. CLOTHES DO NOT DRY

11. TUMBLER OVERHEATING

POSSIBLE CAUSE

TO CORRECT

Heat source inoperative.

• Refer to Paragraph 17.

Too much water in articles being dried.

• Remove excess water.

Clothes load too large.

• Remove part of load. 120 pounds dry weight (AHAM

cotton load) is maximum load.

Improper or inadequate exhaust system.

• Refer to Installation Manual (supplied with tumbler) for

exhaust requirements.

Heat source shuts off prematurely.

• Refer to Paragraph 18.

Drying timer improperly set.

• Set selector for higher setting.

Incorrect voltage.

• Refer to Installation Manual (supplied with tumbler) for

electrical requirements.

Inadequate make-up air.

• Refer to Installation Manual (supplied with tumbler) for

make-up air requirements.

Improper fan rotation.

• May be due to improper wiring resulting in low air flow.

Refer to Installation Manual.

POSSIBLE CAUSE

TO CORRECT

Gas Models: Incorrect main burner orifices.

• Replace orifices.

Gas Models: Gas pressure too high.

• Adjust gas pressure as specified on serial plate.

Steam Models: Steam solenoid valve stuck open.

• Clean solenoid valve and replace if necessary.

Inadequate make-up air.

• Refer to Installation Manual (supplied with tumbler) for

make-up air requirements.

Lint accumulation.

• Remove lint.

Restricted or inadequate exhaust system.

• Remove obstruction or lint build-up from exhaust

ductwork. Refer to the Installation Manual (supplied
with tumbler) for exhaust system requirements.

Inoperative thermostat.

• Replace thermostat.

«
...
12
13
14
15
16
...
»

Содержание AT120CSH









































































Отзывы:

Нет отзывов

Похожие инструкции для AT120CSH

Бренд: Anets Страницы: 26

StarlettePlus-E

Бренд: Parker Страницы: 148

Unimatic TSL WP

Бренд: V-ZUG Страницы: 44

Бренд: KAI Страницы: 13

Бренд: Braun Страницы: 4

Бренд: nedis Страницы: 108

SilentDry MX00206

Бренд: MaxxDrySD Страницы: 4

Fry delight initial

Бренд: TEFAL Страницы: 12

Бренд: Maguire Products Страницы: 39

EconoRed Series

Бренд: VASTEX Страницы: 20

Бренд: Haier Страницы: 15

Бренд: Haier Страницы: 14

Бренд: Haier Страницы: 2

Tiana HW100-HB1297NZP

Бренд: Haier Страницы: 8

XQG50-ABA1100CTX

Бренд: Haier Страницы: 20

HWD100-B14959S8U1

Бренд: Haier Страницы: 40

HWD100-B14876U1

Бренд: Haier Страницы: 32

XQG50-AB1100CTX

Бренд: Haier Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды