Alliance Laundry Systems AT120CSH Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 72

background image

26

M412982

Section 5 Service Procedures

To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the tumbler before servicing.
• Close gas shut-off valve to gas tumbler before servicing.
• Close steam valve to steam tumbler before servicing.
• Never start the tumbler with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be

reconnected to ensure that the tumbler is properly grounded.

W002

WARNING

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

26. LOADING DOOR SWITCH

a. Remove front panel.
b. Disconnect wires from door switch.
c. Remove two switch attaching screws and

remove switch. Refer to Figure 4.

NOTE: Refer to wiring diagram when rewiring
door switch.

27. PUSH-TO-START SWITCH

(Manual Timer Models)
a. Remove four screws holding access panel to

cabinet. Refer to Figure 1.

b. Lift access panel off top edge of front panel and

pull panel forward. Refer to Figure 1.

c. Remove timer box cover. Refer to Figure 1.

d. Remove two screws holding switch to front

panel. Refer to Figure 5.

e. Disconnect wires from switch terminals and

remove switch.

NOTE: Refer to wiring diagram when rewiring
switch.

28. COOLING AND DRYING RUN LIGHTS

(Manual Timer Models)
a. Remove four screws holding access panel to

cabinet. Refer to Figure 1.

b. Lift access panel off top edge of front panel and

pull panel forward. Refer to Figure 1.

c. Remove timer box cover. Refer to Figure 1.

d. Disconnect light wire leads. Refer to Figure 5.

e. Compress locking tabs on sides of light and

push light through front panel.

29. RELAY

a. Remove four screws holding access panel to

cabinet. Refer to Figure 1.

b. Lift access panel off top edge of front panel and

pull panel forward. Refer to Figure 1.

c. Remove timer box cover. Refer to Figure 1.

d. Disconnect wires from relay.

e. Remove two screws holding relay to bracket.

Refer to Figure 5.

NOTE: Refer to wiring diagram when rewiring
relay.

Figure 4

To reduce the risk of serious injury or
death, loading door switch MUST be
reinstalled after service is completed.

W328

WARNING

SWITCH

ATTACHING

SCREWS

T315PE1A

DOOR

SWITCH

ACTUATOR

«
...
23
24
25
26
27
...
»

Содержание AT120CSH









































































Отзывы:

Нет отзывов

Похожие инструкции для AT120CSH

Spacemaker DSKS333EC

Бренд: GE Страницы: 3

Бренд: INNOLIVING Страницы: 20

Бренд: Newal Страницы: 21

Бренд: Kalorik Страницы: 72

Бренд: Salton Страницы: 10

Бренд: Mediclinics Страницы: 6

Бренд: Hotpoint Страницы: 84

Бренд: Haier Страницы: 20

Бренд: Haier Страницы: 20

Бренд: Haier Страницы: 24

Бренд: Haier Страницы: 34

Бренд: Haier Страницы: 16

Бренд: Haier Страницы: 16

Бренд: Haier Страницы: 36

Ginesis HLF103Q

Бренд: Haier Страницы: 14

Бренд: Haier Страницы: 20

GDZ5.0-61WH HA AA

Бренд: Haier Страницы: 11

Бренд: Haier Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды