Alliance Laundry Systems AT120CSH Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 72

background image

10

M412982

Section 3 Troubleshooting

To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the tumbler before servicing.
• Close gas shut-off valve to gas tumbler before servicing.
• Close steam valve to steam tumbler before servicing.
• Never start the tumbler with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be

reconnected to ensure that the tumbler is properly grounded.

W002

WARNING

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

2. MOTOR OVERLOAD PROTECTOR CYCLES REPEATEDLY

3. MOTOR RUNS BUT CYLINDER DOES NOT TURN.

4. MOTOR DOES NOT STOP

POSSIBLE CAUSE

TO CORRECT

Incorrect voltage.

• Refer to Installation Manual (supplied with tumbler) for

electrical requirements.

Clothes load too large.

• Remove part of load.

Cylinder binding.

• Check cylinder for binding. Refer to Adjustment Section

in this manual for cylinder adjustment.

Inadequate wiring.

• Check with local power company to ensure that wiring is

adequate.

Inadequate make-up air.

• Refer to Installation Manual (supplied with tumbler) for

make-up air requirements.

Poor housekeeping.

• Clean lint accumulation on and around the motor.

Broken, loose or incorrect wiring.

• Refer to wiring diagram located on back of tumbler or in

literature packet.

POSSIBLE CAUSE

TO CORRECT

Motor drive pulley loose.

• Tighten drive pulley bushing screws.

Broken or loose cylinder belts.

• Replace or adjust belts.

Broken or loose drive belt.

• Replace or adjust belt.

Cylinder binding.

• Check cylinder for binding. Refer to Adjustment Section

in this manual for proper cylinder adjustment.

POSSIBLE CAUSE

TO CORRECT

Inoperative door switch or switch is out-of-
adjustment.

• Test switch and replace if inoperative. Refer to

Adjustment Section in this manual for proper switch
adjustment.

Inoperative timer.

• Test timer and replace if inoperative.

Incorrect wiring.

• Refer to wiring diagram located on back of tumbler or in

literature packet.

Inoperative motor contactor.

• Test motor contactor and replace if inoperative.

«
...
8
9
10
11
12
...
»

Содержание AT120CSH









































































Отзывы:

Нет отзывов

Похожие инструкции для AT120CSH

Бренд: Jata Страницы: 12

Бренд: Cajun Страницы: 12

Бренд: GE Страницы: 72

Бренд: SEVERIN Страницы: 1

Бренд: Euro-Pro Страницы: 7

Бренд: Smeg Страницы: 16

Бренд: Expondo Страницы: 15

Бренд: Candy Страницы: 26

Бренд: Candy Страницы: 32

Бренд: Zanussi Страницы: 9

Бренд: Zanussi Electrolux Страницы: 31

Бренд: Indesit Страницы: 84

Бренд: Farouk Страницы: 2

Бренд: KitchenAid Страницы: 64

Бренд: KitchenAid Страницы: 5

Бренд: KitchenAid Страницы: 6

Бренд: KitchenAid Страницы: 16

Бренд: KitchenAid Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды