Alliance Laundry Systems AT120CSH Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 72

background image

28

M412982

Section 5 Service Procedures

To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the tumbler before servicing.
• Close gas shut-off valve to gas tumbler before servicing.
• Close steam valve to steam tumbler before servicing.
• Never start the tumbler with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be

reconnected to ensure that the tumbler is properly grounded.

W002

WARNING

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

31. REVERSING/NONREVERSING SWITCH

(Manual Timer Models)
a. Remove four screws holding access panel to

cabinet. Refer to Figure 1.

b. Lift access panel off top edge of front panel and

pull panel forward.

c. Remove control box cover. Refer to Figure 2.

d. Disconnect the wires from the back of the

switch. Refer to Figure 6.

e. Depress tabs and pull switch out.

(OPL Micro Control MM Models)
Refer to Figure 7
a. Remove micro control face plate.

b. Remove two micro control mounting plate

screws, and rotate mounting plate downward.

c. Disconnect wires from back of switch.

d. Depress tabs and pull switch out.

32. CONTROL THERMOSTAT

(Manual Timer Models)
a. Remove four screws holding access panel to

cabinet. Refer to Figure 1.

b. Lift access panel off top edge of front panel and

pull panel forward.

c. Remove control box cover. Refer to Figure 2.

d. Pull knob off thermostat. Refer to Figure 6.

e. Disconnect wires from thermostat.

Figure 6

TMB1336P

INSTANT

ELECTRONIC

IGNITION

CONTROL

LIGHTS

THERMOSTAT

ATTACHING

SCREW

THERMOSTAT

KNOB

REVERSING/NONREVERSING

SWITCH

PROBE

THERMOSTAT

TUBE

CONTACT

BLOCK

EMERGENCY STOP

BUTTON

TEMPERATURE

GRAPHIC

PANEL

«
...
25
26
27
28
29
...
»

Содержание AT120CSH









































































Отзывы:

Нет отзывов

Похожие инструкции для AT120CSH

Бренд: GE Страницы: 44

Бренд: R.G.V. Страницы: 40

Бренд: VOX electronics Страницы: 33

Бренд: Maytag Страницы: 44

Бренд: MAGUIRE Страницы: 127

Бренд: Grundig Страницы: 25

Frialator SF14 UFM

Бренд: Pitco Страницы: 43

Бренд: Blomberg Страницы: 44

Бренд: TriStar Страницы: 10

Бренд: Parker Страницы: 38

Бренд: CombiSteel Страницы: 31

DOMINATOR PLUS E3830

Бренд: Falcon Страницы: 13

NA-S086M4 Series

Бренд: Panasonic Страницы: 33

Classic FP5500P

Бренд: Sunbeam Страницы: 36

Бренд: Blue Seal Страницы: 40

Бренд: GEAppliances Страницы: 15

SalonDry Compact HP4960

Бренд: Philips Страницы: 88

Бренд: Whirlpool Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды