background image

EconoRed (ER) Series Dryers 

Assembly, Operating, and Maintenance Instructions for  

ER-II-30, ER-II-54, ER-III-30, & ER-III-54 Dryers 

(EC-II-30 Shown) 

Doc. # 01-32-001A 



Introduction / Safety  

2-3 



Assembly 

4-8 



SHD Drive 



Belt Tracking 

10 



Component Identification 

11 



Controls 

12-13 



Operation 

14-15   



Maintenance 

16 



Drive Chain Adjustment 

17 



Troubleshooting 

18-19 



Warranty / Terms & Conditions 

20 

Serial Number: 

(Please log your machine's serial number and date of purchase for future reference.) 

Date:____

/

____

/

______ 

Electrical Drawing #: 

Rev:______ 

Pg # 

VTX 

Vastex E-mail assistance 

  

Purchasing & Product Info: 

[email protected] 

  

Electrical Support: 

[email protected] 

  

Tech Support, Mechanical Setup, and Operation: 

[email protected] 

  

Screen Printing Issues & Support: 

[email protected]

  

Original Instructions 

Vastex International, Inc. 

7 Emery Street 

Bethlehem, PA  

Phone# 610 625-2702 Fax# 610 625-2775  

Web Site  www.vastex.com 

 

Authorized Representative in Europe: 

Certification Experts BV 

Nieuwstad 100 1381 CE Weesp,  

The Netherlands  

Tel : + 31 (0) 294 – 48 33 55  

Fax : + 31 (0) 294 – 41 46 87  

Year of Manufacture:  

20____ 

Содержание EconoRed Series





















Отзывы: