Alliance Laundry Systems AT120CSH Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 72

background image

38

M412982

Section 5 Service Procedures

To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the tumbler before servicing.
• Close gas shut-off valve to gas tumbler before servicing.
• Close steam valve to steam tumbler before servicing.
• Never start the tumbler with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be

reconnected to ensure that the tumbler is properly grounded.

W002

WARNING

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

48. DRIVE BELT

Refer to Figure 15.
a. Support drive guard cover and remove screws

holding guard to rear of tumbler. Refer to
Figure 13.

b. Loosen the four jackshaft assembly attaching

screws. Refer to Figure 14.

c. Rotate the adjusting nuts counterclockwise

(approximately three turns).

d. Slide jackshaft assembly upwards to loosen the

cylinder belts.

e. Remove cylinder belts.

f. Remove drive belt.

NOTE: After reinstalling drive belt, adjust cylinder
belts then drive belt.

49. STEP PULLEY ASSEMBLY

Refer to Figure 15.
a. Support drive guard cover and remove screws

holding guard to rear of tumbler. Refer to
Figure 13.

b. Remove cylinder and drive belts.
c. Remove snap ring and pull step pulley off of

jackshaft.

50. CYLINDER SHEAVE

Refer to Figure 15.
a. Support drive guard cover and remove screws

holding guard to rear of tumbler. Refer to
Figure 13.

b. Loosen the four jackshaft assembly attaching

screws. Refer to Figure 14.

c. Rotate the adjusting nuts counterclockwise

(approximately three turns).

d. Slide jackshaft assembly upwards to loosen the

cylinder belts.

e. Remove cylinder belts.

f. Remove bushing setscrew. Refer to Figure 15.

g. Remove screws from tapered bushing.
h. Remove tapered bushing by putting the screws

removed in step “g” into the threaded holes in
the bushing. Turning the screws inward will
force the bushing out of the cylinder sheave.

i. Remove cylinder sheave.

Figure 15

T317PE1A

CYLINDER

BELT

BOLT

JACKSHAFT

ASSEMBLY

CYLINDER

SHEAVE

STEP

PULLEY

SNAP

RING

TAPERED

BUSHING

DRIVE

BELT

SETSCREW

«
...
35
36
37
38
39
...
»

Содержание AT120CSH









































































Отзывы:

Нет отзывов

Похожие инструкции для AT120CSH

Бренд: Canmac Страницы: 17

Бренд: Falcon Страницы: 6

Бренд: Falcon Страницы: 5

DOMINATOR PLUS Series

Бренд: Falcon Страницы: 12

Бренд: gama.professional Страницы: 14

Бренд: Gourmia Страницы: 20

Бренд: Cosori Страницы: 23

COMPACT PRO CV4802Y0

Бренд: Rowenta Страницы: 2

Бренд: U.S. Range Страницы: 20

Бренд: Asko Страницы: 12

Бренд: Aurora Страницы: 8

Бренд: Maestro Страницы: 48

Бренд: DAN DRYER Страницы: 4

Бренд: LG Страницы: 38

Бренд: LG Страницы: 41

Бренд: LG Страницы: 16

Бренд: LG Страницы: 32

Бренд: LG Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды