Alliance Laundry Systems AT120CSH Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 72

background image

40

M412982

Section 5 Service Procedures

To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the tumbler before servicing.
• Close gas shut-off valve to gas tumbler before servicing.
• Close steam valve to steam tumbler before servicing.
• Never start the tumbler with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be

reconnected to ensure that the tumbler is properly grounded.

W002

WARNING

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

54. TRUNNION BEARINGS

Refer to Figure 17.
a. Remove front panel assembly.
b. Place blocks under cylinder so that cylinder

will stay level while trunnion bearings are
being replaced.

c. Remove cylinder sheave.

d. Loosen the front and rear adjusting screws.

e. Loosen setscrews holding bearings to shaft.

f. Remove bearing mounting screws.

g. Remove rear bearing.
h. Remove screws that hold mounting bracket to

tumbler.

i. Remove mounting bracket.
j. Remove front bearing mounting nuts.

k. Loosen setscrews holding bearing to shaft.

l. Remove front bearing.

Figure 17

T533P

REAR

ADJUSTING

SCREW

BEARING

MOUNTING

NUT

MOUNTING

BRACKET

BEARING

MOUNTING

SCREW

SETSCREWS

REAR

BEARING

ASSEMBLY

FRONT

BEARING

ASSEMBLY

MOUNTING BRACKET

ATTACHING

SCREW

FRONT

ADJUSTING

SCREW

SETSCREWS

«
...
37
38
39
40
41
...
»

Содержание AT120CSH









































































Отзывы:

Нет отзывов

Похожие инструкции для AT120CSH

Бренд: Dean Страницы: 2

Бренд: FERREX Страницы: 20

Бренд: Remington Страницы: 9

Бренд: Maytag Страницы: 20

Бренд: Frymaster Страницы: 24

Бренд: Pro-Elec Страницы: 4

MAXX PLUS FT 47822 SS MAXX PLUS FT 47824 SS MAXX PLUS FT 50876 SS

Бренд: Kalorik Страницы: 40

Бренд: ELEKTRA Страницы: 56

Бренд: GE Страницы: 48

Бренд: OldScool Страницы: 11

Бренд: Kenmore Страницы: 8

Бренд: Kenmore Страницы: 1

Бренд: Electrolux Страницы: 2

Бренд: Electrolux Страницы: 24

Бренд: Electrolux Страницы: 2

Бренд: Electrolux Страницы: 11

Бренд: Electrolux Страницы: 2

Бренд: Electrolux Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды