manualshive.com logo in svg

Allen-Bradley ControlLogix 1756-DMD30, Руководство пользователя, Страница: 240 / 369

Поделиться
Скачать
Allen-Bradley ControlLogix 1756-DMD30 Скачать руководство пользователя страница 240

Publication 1756-UM522B-EN-P - February 2003

B-160        1756-DMD30 Specific Information

Parameter 323 [Fault Status 1]

This parameter indicates the occurance of exception events that have 
been configured as fault conditions. These events are from parameter 
320 [Exception Event1]. These bits are latched until they are reset by 
setting bit 19 [Clear Fault] of parameter 152 [Applied LogicCmd]. After 
turning the Clear Fault bit on, the drive may be re-started after turning 
the command bits off and then back on again. If the fault conditions 
still exist, the identifying bit in this parameter will immediately be set 
again. The fault conditions reported in this register result in turning 
off the drive.

Bit 7

Res Bal OK

This bit is set when the resolver balance calibration 
procedure is complete. This procedure is performed when 
parameter 168 [Drive I/O Ctrl] bit 6 [Enbl Res Bal] is set and 
the motor is turning.

Bit 8

StrobeDetect

This bit is set when the external strobe on the motor’s 
resolver is detected. Parameter 2136 [Res Strobe Posit] 
displays the position of the resolver at the time of the 
strobe. Note that this bit is set for only one scan allowing a 
strobe to be detected every scan. The Logix task must check 
the External Strobe Detected bit each scan to ensure the 
validity of the strobe data in Parameter 2136.

Bit 9

Strobe Level

This bit is set or reset  when the external strobe is detected. 
It indicates whether the external strobe level was rising (1) 
or falling (0).

Bit

Fault Name

Fault Description

Bit 0

Abs OverSpd

Motor speed has exceed the value in parameter 335 [Abs 
OverSpd Lim].

Bit 1

SpdRef Decel 

The drive has failed to achieve a zero speed condition.

Bit 6

Ctrl EE Mem

Not Used

Bit 7

Slink HW

Not Used

Bit 8

Slink Comm

A SynchLink communication failure has occurred.  These 
faults are enumerated in parameter 1229 [SL Error Status].

Bit 10

Mtr OL Trip

A Mtr OL Trip exception event has faulted the drive module.  
Refer to parameter 371 [Mtr OL Trip Cnfg], parameter 336 
[Service Factor], parameter 337 [Mtr I2T Curr Min], and 
parameter 338 [Mtr I2T Spd Min].

Bit 11

Mtr OL Pendg

A Mtr OL Pendg exception event has faulted the drive 
module.  Refer to parameter 372 [Mtr OL Pend Cnfg], 
parameter 336 [Service Factor], parameter 337 [Mtr I2T Curr 
Min], and parameter 338 [Mtr I2T Spd Min].

Bit

Fault Name

Fault Description

Содержание ControlLogix 1756-DMD30


















































































































































































































































































































































































Отзывы:

Нет отзывов