manualshive.com logo in svg

Allen-Bradley 5069-IA16, Руководство пользователя

Allen-Bradley 5069-IA16 - периферийный ввод/вывод с 16 цифровыми входами. Пользовательский мануал доступен для бесплатного скачивания на manualshive.com. Инструкции по эксплуатации, технические характеристики и другая полезная информация об устройстве доступны в руководстве пользователя. Получите свой экземпляр прямо сейчас!

Поделиться
Скачать
background image

Rockwell Automation Publication 5069-UM004A-EN-P - April 2019

13

Preface

Terminology

The following table defines terms that are used in this manual.

Table 1 - Terminology Used throughout the Manual

Abbreviation

Full Term

Definition

1oo2

One out of Two

Identifies the programmable electronic controller architecture.

CIP™

Common Industrial Protocol

An industrial communication protocol that is used by Logix 5000-based automation systems on EtherNet/IP, 
ControlNet®, and DeviceNet® communication networks.

CIP Safety™

Common Industrial Protocol – 
Safety Certified

SIL-rated version of CIP.

—

Connection

Logical communication channel for communication between nodes. Connections are maintained and controlled 
between masters and slaves.

CL

Claim Limit

The maximum safety integrity level (SIL) that can be achieved.

DC

Diagnostic Coverage

The ratio of the detected failure rate to the total failure rate.

EN

European Norm.

The official European Standard.

GSV

Get System Value

A ladder logic instruction that retrieves specified controller status information and places it in a destination tag.

—

Multicast

The transmission of information from one sender to multiple receivers.

MTTF

Mean Time to Failure

The length of time that a device or other product is expected to remain reliable in operation.

NAT

Network Address Translation

The translation of an Internet Protocol (IP) address to another IP address on another network.

ODVA

Open DeviceNet Vendor Association

A nonprofit association of vendors that are established for the promotion of CIP networks.

PFD

Probability of a dangerous failure on 
demand 

The average probability of a system to fail to perform its design function on demand.

PFH

Average frequency of a dangerous 
failure per hour

The probability of a system to have a dangerous failure occur per hour.

PL

Performance Level

ISO 13849-1 safety rating.

—

Proof test

Periodic test that detects failures in a safety-related system so that, if necessary, the system can be restored to an 
as-new condition or as close as practical to this condition.

SC

Systematic Capability

A confidence that the systematic safety integrity meets the requirements of the specified safety integrity level 
(SIL). (from IEC 61508-4)

SFF

Safe Failure Fraction

The sum of safe failures plus the sum of dangerous detected failures divided by the sum of all failures.

SIL

Safety Integrity Level 

A relative level of risk-reduction that is provided by a safety function, or to specify a target level of risk reduction.

SIL CL

SL Claim Limit

The maximum safety integrity level (SIL) that can be achieved.

SNN

Safety Network Number 

Safety network number, which uniquely identifies a network across all networks in the safety system. You are 
responsible for assigning a unique number for each safety network or safety subnet within a system.

SRT

Safety Reaction Time

A consideration of delays or latencies within the safety system.

—

Standard

Devices or portions of devices that do not participate in the safety function.

—

Unicast

The transmission of information from one sender to one receiver.

Содержание 5069-IA16









































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 5069-IA16

Watts OneFlow OFTWH-R Installation And Operation Manual preview
OneFlow OFTWH-R
Бренд: Watts Страницы: 8
Measurement Computing CIO-DAS1401/12 User Manual preview
CIO-DAS1401/12
Бренд: Measurement Computing Страницы: 32
Vestil WTJ-20 Series Instruction Manual preview
WTJ-20 Series
Бренд: Vestil Страницы: 11
Medion LIFE P64077 Instruction Manual preview
LIFE P64077
Бренд: Medion Страницы: 308
NAIM LANGS Owner'S Manual preview
LANGS
Бренд: NAIM Страницы: 51
Chal-tec ONECONCEPT 10029361 Manual preview
ONECONCEPT 10029361
Бренд: Chal-tec Страницы: 29
Instron Torsion Add-on Version 3 Operator'S Manual preview
Torsion Add-on Version 3
Бренд: Instron Страницы: 32
Pure Water PWS BEV-300 Series Owner'S Manual preview
PWS BEV-300 Series
Бренд: Pure Water Страницы: 35
Ravaglioli KPS234HEPO Manual preview
KPS234HEPO
Бренд: Ravaglioli Страницы: 60
Champion Autolift FP8000 Installation Manual preview
FP8000
Бренд: Champion Autolift Страницы: 14
ZKTeco VDPO3-B3 Quick Installation Manual preview
VDPO3-B3
Бренд: ZKTeco Страницы: 15
Ricatech RMC100 User Manual preview
RMC100
Бренд: Ricatech Страницы: 64
R. Beck Maschinenbau HS 1000/FH Operating Manual preview
HS 1000/FH
Бренд: R. Beck Maschinenbau Страницы: 31
Rotary SL230RA-PE Installation Instructions Manual preview
SL230RA-PE
Бренд: Rotary Страницы: 30
Omron C500-ASC04 Operation Manual preview
C500-ASC04
Бренд: Omron Страницы: 154
blupura PANTAREI Use & Maintenance Manual preview
PANTAREI
Бренд: blupura Страницы: 28
LENCO MDV-15 Instruction Manual preview
MDV-15
Бренд: LENCO Страницы: 24
ICP DAS USA MQ-7200M Series User Manual preview
MQ-7200M Series
Бренд: ICP DAS USA Страницы: 66

Бренды по названию

Популярные бренды

Загрузить еще бренды