manualshive.com logo in svg

Allen-Bradley 5069-IA16, Руководство пользователя

Поделиться
Скачать
Allen-Bradley 5069-IA16 Скачать руководство пользователя страница 242

242

Rockwell Automation Publication 5069-UM004A-EN-P - April 2019

Appendix B

   Module Tag Definitions

Event Output Tags

Table 66

 describes the 5069-IB16F module event output tags. The event 

output tags are displayed only if Data with Events is selected in the Module 
Definition window.

Table 66 - 5069-IB16F Module Event Output Tags

 Name

Size

Definition

Valid Values

Eventxx.En

BOOL

When set, the corresponding event trigger definition is 
active and events are triggered when conditions match 
the definition.

0 = Event trigger definition is not active and 
events are not triggered when conditions match 
the definition
1 = Event trigger definition is active and events 
are triggered when conditions match the 
definition

Eventxx.EventRisingEn

BOOL

When set an event is to trigger each time a condition 
change results in conditions that match the event trigger 
definition.

0 or 1

Eventxx.EventFallingEn

BOOL

When set, an event is to trigger each time a condition 
change results in conditions that no longer match the 
event trigger definition.

0 or 1

Eventxx.LatchEn

BOOL

When set, events are latched until acknowledged. A new 
event is lost if the previous event has not been 
acknowledged. When not set, new events overwrite old 
events.

• 0 = Not latched (default)
• 1 = Latched

Eventxx.ResetEvent

BOOL

When transitions from 0 to 1, resets all events and clears 
the event queue on the channel.

• 0 = Events are not cleared.
• 1 = Events are cleared when a rising edge 

occurs.

Eventxx.IndependentConditionTriggerEn

BOOL

For events, determines whether each condition that is 
indicated in the trigger definition can initiate an event 
independently.

• 0 = When all selected conditions achieve the 

configured values, an event is triggered.

• 1 = When any selected condition achieves the 

configured value, an event is triggered.

Eventxx.EventNumberAck

DINT

The controller writes back the 
EI:Event[<n>].EventNumber into this 
EO:Event[<n>].EventNumberAck to indicate receipt of 
the event. All events with I:EventNumbers that occurred 
before EventNumberAck is acknowledged.

All values

Eventxx.CounterxxSelect

BOOL

When set, indicates that the corresponding counter is to 
participate in the event trigger definition.

0 = Corresponding counter does not participate in 
the event trigger definition
1= Corresponding counter participates in the 
event trigger definition

Eventxx.PtxxDataSelect

BOOL

When set, indicates that the corresponding data value is to 
participate in the event trigger definition.

0 or 1

Eventxx.CounterxxValue

BOOL

If the counter function is selected in the event trigger 
definition, this member indicates that value that is to 
trigger the event.

0 or 1

Eventxx.PtxxDataValue

BOOL

Indicates the input value of the event point data.

• 0 = Input inactive
• 1 = Input active

Содержание 5069-IA16









































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды