manualshive.com logo in svg

Allen-Bradley 5069-IA16, Руководство пользователя

Allen-Bradley 5069-IA16 - периферийный ввод/вывод с 16 цифровыми входами. Пользовательский мануал доступен для бесплатного скачивания на manualshive.com. Инструкции по эксплуатации, технические характеристики и другая полезная информация об устройстве доступны в руководстве пользователя. Получите свой экземпляр прямо сейчас!

Поделиться
Скачать
background image

Rockwell Automation Publication 5069-UM004A-EN-P - April 2019

279

Application and Wiring Examples for Safety Modules     

Appendix C

For 

Cat.4

 applications, if your application remains in safe state, that is, the 

output is off, for a prolonged duration, we recommend that you take one of the 
following actions:

• Apply output monitoring at the actuator. The monitoring can be direct 

or indirect. 

• Limit the safe state to no more than 24 hours.
• Conduct functional test if safe state dwell time increases.

5069-OBV8S

OUTPUT

0

7

6

5

4

3

2

1

17

16

15

14

13

12

11

10

9

8

Safety Output 0 P (Sourcing)

LA +

LA –

Safety Output 3 P (Sourcing)

Safety Output 4 P (Sourcing)

Safety Output 4 N (Sinking)

Safety Output 1 N (Sinking)

Safety Output 5 P (Sourcing)

Safety Output 5 N (Sinking)

Safety Output 6 P (Sourcing)

Safety Output 6 N (Sinking)

Safety Output 7 P (Sourcing)

Safety Output 7 N (Sinking)

Safety Output 3 N (Sinking)

Safety Output 2 N (Sinking)

Safety Output 2 P (Sourcing)

Safety Output 1 P (Sourcing)

Safety Output 0 N (Sinking)

Actuator LA Power

In this wiring configuration, you must connect the 

LA+ terminal to 

an SELV/PELV-listed

 power supply.

The LA+ and LA- on the actuator must be connected to the same 
power supply as the LA+ and LA- on the module.

24V DC 

SELV/PELV-listed 

power supply

–

+

M

K1

K2

LA –

LA +

Channel Connections

This wiring example shows connections to the P-N pair for Safety 
Output 0. You are not limited to using channel 0 in this mode. You can 
use all channel pairs as determined by your application.

LA Power

The Local Actuator (LA+ and LA –) power connections are used to 
supply field-side power to the module.
• The 5069-OBV8S and 5069-OBV8SK modules 

do not draw 

current from the SA Power bus

. The modules are DC type 

modules. Therefore, you must install them on an SA Power bus that 
uses DC power.

• If you install modules in a system that use AC SA power and DC SA 

power, you must install them on separate SA power buses.

• You use a 5069-FPD field potential distributor to establish a new SA 

Power bus in a system. SA Power buses are isolated from each 
other. To keep the modules on separate SA Power buses, complete 
the following steps.
1. Install the modules that use one type of SA power, for example 

DC, to the right of the adapter or controller, that is, the first SA 
Power bus.

2. Install the 5069-FPD field potential distributor to establish a 

second SA Power bus.

3. Install the modules that use the other type of SA power, for 

example AC, on the second SA Power bus.

• We 

strongly recommend

 that, if you have a direct connection 

between the safety output module and an input module and those 
modules are powered by separate power supplies, that you 
connect SA- and LA- together. This practice helps to eliminate 
grounding float from disrupting diagnostics. 

Connection Pairs

The terminals for each channel function as a Bipolar connection pair 
when you use a 5069-OBV8S or 5069-OB8VSK module in Bipolar 
switching mode. For example, the Safety Output 0 P (Sourcing) 
terminal and Safety Output 0 N (Sinking) terminal are a Bipolar 
connection pair. That is, they are a P-N pair.
When the module is in Bipolar switching mode, you must connect the 
device to both terminals. 

Содержание 5069-IA16









































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 5069-IA16

Samsung MX-F870 Service Manual preview
MX-F870
Бренд: Samsung Страницы: 70
Samsung MM-L7 Manual Del Usuario preview
MM-L7
Бренд: Samsung Страницы: 21
Samsung MM-ZB9 Service Manual preview
MM-ZB9
Бренд: Samsung Страницы: 28
ICP DAS USA SG-3016 User Manual preview
SG-3016
Бренд: ICP DAS USA Страницы: 5
ICP DAS USA M-7000 series Quick Start Manual preview
M-7000 series
Бренд: ICP DAS USA Страницы: 7
National Instruments NI 9469 Getting Started preview
NI 9469
Бренд: National Instruments Страницы: 13
National Instruments PXIe-4339 Calibration Procedure preview
PXIe-4339
Бренд: National Instruments Страницы: 30
Measurement Computing CIO-DAS1401/12 User Manual preview
CIO-DAS1401/12
Бренд: Measurement Computing Страницы: 32
Genie Runabout GR-12 Operator'S Manual preview
Runabout GR-12
Бренд: Genie Страницы: 35
Battery Watering Technologies PW-180 Installation And Operation Instructions preview
PW-180
Бренд: Battery Watering Technologies Страницы: 2
Teac GF-650 Service Manual preview
GF-650
Бренд: Teac Страницы: 23
National Instruments NI 653 Series User Manual preview
NI 653 Series
Бренд: National Instruments Страницы: 151
Farfisa Sette SE4252 Instruction Manual preview
Sette SE4252
Бренд: Farfisa Страницы: 36
Nortek Security & Control MIGHTY MULE MM136 Instructions For Wired And Wireless Installations preview
MIGHTY MULE MM136
Бренд: Nortek Security & Control Страницы: 11
XtendLan DPM-D2101TMD User Manual preview
DPM-D2101TMD
Бренд: XtendLan Страницы: 12
Commax DRC-4BGN User Manual preview
DRC-4BGN
Бренд: Commax Страницы: 8
Ezon SHT-3107XM/EN User Manual preview
SHT-3107XM/EN
Бренд: Ezon Страницы: 9
HEIN-WERNER AUTOMOTIVE HW93805 Manual preview
HW93805
Бренд: HEIN-WERNER AUTOMOTIVE Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды