manualshive.com logo in svg

Allen-Bradley 5069-IA16, Руководство пользователя

Поделиться
Скачать
Allen-Bradley 5069-IA16 Скачать руководство пользователя страница 248

248

Rockwell Automation Publication 5069-UM004A-EN-P - April 2019

Appendix B

   Module Tag Definitions

Ptxx.InputOnOffFilter

SINT

The amount of time that a signal must be in the off state 
before the input data indicates the off state. The amount 
of time is indicated using an enumeration. Not all 
products support all enumeration values.

• 5 = 0 μs
• 6 = 5 μs
• 7 = 10 μs
• 8 = 20 μs
• 9 = 50 μs
• 10 = 100 μs
• 11 = 200 μs
• 12 = 500 μs
• 13 = 1 ms
• 14 = 2 ms
• 15 = 5 ms
• 16 = 10 ms
• 17 = 20 ms
• 18 = 50 ms

Ptxx.ChatterTime

INT

A value from 1…10000 ms in whole ms increments.

1…10000

Ptxx.ChatterCount

SINT

The number of input changes that are considered Chatter.

• 0 = Disabled
• 2…127 = Enabled

Ptxx.CaptureOffOnEn

BOOL

Enables capturing Off to On time stamps. If cleared, point 
does not record Off to On time stamps.

• 0 = Capture disabled (default) for OFF to ON 

input transitions

• 1 = Capture enabled for OFF to ON input 

transitions

Ptxx.CaptureOnOffEn

BOOL

Enables capturing On to Off time stamps. If cleared, point 
does not record On to Off time stamps.

• 0 = Capture disabled (default) for ON to OFF 

input transitions

• 1 = Capture enabled for ON to OFF input 

transitions

Ptxx.TimestampLatchEn

BOOL

When this bit is set, timestamps are latched; this means 
that a Timestamp is not overwritten until acknowledged. 
All subsequent transitions on that point are ignored until 
acknowledged/reset. If the bit is not set, the new LO 
Timestamp overwrites the first LO Timestamp 
immediately, even if the controller has yet to extract that 
data. 
The timestamp can also be acknowledge if the 
Ptxx.TimestampxxxxxNumber input tag value is written to 
the Ptxx.TimestampxxxxxNumberAck output tag value.
It is worth noting that writing the input tag value to the 
output tag value, clears the Ptxx.Timestampxxxxx input 
tag value.

(1)

• 0 = Timestamps are overwritten with each 

successive COS transition.

• 1 = Timestamps are latched until 

acknowledged.

(1) In this case, the xxxxx in the tag names represents OffOn or OnOff tags based on what transition occurred. That is, a change in state from Off to On or On to Off.

Table 69 - 5069-IB6F-3W Configuration Tags

 Name

Size

Definition

Valid Values

Содержание 5069-IA16









































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды