manualshive.com logo in svg

Allen-Bradley 5069-IA16, Руководство пользователя

Поделиться
Скачать
Allen-Bradley 5069-IA16 Скачать руководство пользователя страница 253

Rockwell Automation Publication 5069-UM004A-EN-P - April 2019

253

Module Tag Definitions   

Appendix B

Counterxx.Done

BOOL

Indicates that the I:Count tag ≥ O:Preset.G430.

0 or 1

Counterxx.Rollover

BOOL

The counter counted up to RolloverValue - 1 (for HSC) or 
Preset -1 (for simple counters) and then continued 
counting from the O:Rollunder (for HSC) or 0 (for simple 
counters). The O:RolloverAck bit transitioning from 0 to 1 
or the O:Reset transitioning from 0 to 1 clears the bit.

0 or 1

Counterxx.Count

DINT

The number of input transitions counted by a counter.

All values.

EventStatusx.CIPSyncTimeout

BOOL

Indicates that the module was once synced with a 1588 
master, but is not now due to a timeout.

• 0 = A valid time master has not timed out.
• 1 = A valid time master was detected on the 

backplane, but the time master has timed out. 
The module is using its local clock and can be 
drifting away from the last known time 
master.

EventStatusx.CIPSyncValid

BOOL

Indicates whether the module is synced with a 1588 
master.

• 0 = CIP Sync is not available
• 1 = CIP Sync is available

EventStatusx.EventDropped

BOOL

Indicates when an event has been discarded because 
events are occurring faster than they are being 
acknowledged.

• 0 = An event status has not been dropped
• 1 = An event status has been dropped

EventStatusx.EventNumber

DINT

Running count of events, which increments by one each 
new time event. The originator sets the Event Number Ack 
to the Event Number to acknowledge receipt of the event. 
When the EventNumber reaches it maximum value and 
rolls over it is to roll over to 1, not 0. 

All values.

EventStatusx.EventReset

BOOL

When EO.Event[<n>].ResetEvent transitions from 0 to 1, 
I.EventStatus[<n>].EventReset transitions to 1 to indicate 
that the reset was received and completed. It stays 1 until 
EO.Event[<n>].ResetEvent transition to zero.

• 0 = Do not reset
• 1 = Reset

EventStatusx.EventsPending

SINT

The number of events currently queued in the modules. A 
value greater than zero indicates that the controller is not 
currently keeping up with the rate of events.

All positive values.

Ptxx.Data

BOOL

Indicates the current input value.

• 0 = Off
• 1 = On

Ptxx.Fault

BOOL

Indicates that channel data is inaccurate and 

cannot be 

trusted

 for use in the application.

For more information, see 

Module Data Quality Reporting 

on page 71

.

• 0 = Good data
• 1 = Bad data (Faulted)

If the tag is set to 1, you must troubleshoot the 
module to correct the cause of the inaccuracy.

IMPORTANT

: Once the condition that causes 

the tag to change to 1 is removed, the tag 
automatically resets to 0.

Ptxx.Uncertain

BOOL

Indicates that the channel data can be inaccurate but the 

degree of inaccuracy is not known

.

For more information, see 

Module Data Quality Reporting 

on page 71

.

• 0 = Good data

• 1 = Uncertain data

If the tag is set to 1, you must troubleshoot the 
module to correct the cause of the inaccuracy.

IMPORTANT

: Once the condition that causes 

the tag to change to 1 is removed, the tag 
automatically resets to 0.

Table 72 - 5069-IB6F-3W Module Input Tags

 Name

Size

Definition

Valid Values

Содержание 5069-IA16









































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды