manualshive.com logo in svg

Allen-Bradley 5069-IA16, Руководство пользователя

Поделиться
Скачать
Allen-Bradley 5069-IA16 Скачать руководство пользователя страница 276

276

Rockwell Automation Publication 5069-UM004A-EN-P - April 2019

Appendix C

      Application and Wiring Examples for Safety Modules

When the module is wired as shown, and the requirements listed are met in the 
project of the safety controller, it is suitable for applications that are rated up 
to, and including, 

Category 3

 as defined in ISO 13849-1. 

To achieve that suitability rating, you must perform diagnostic testing of the 
safety function. Configure the safety input channel for Safety Pulse Test to test 
the circuit for short circuits to 24V DC.

5069-IB8S

Safety Input 0

Safety Input 1

Safety Input 2

Safety Input 3

Safety Input 4

Safety Input 5

Safety Input 6

Safety Input 7

Test Output 0

Test Output 0

Test Output 1

Test Output 1

Test Output/Muting Output 2

Test Output/Muting Output 2

Test Output/Muting Output 3

Test Output/Muting Output 3

COM

COM

Channel Connections

The diagram shows devices that are connected to 
safety input channel 3 and test output channel 0. You 
are not restricted to using only those channels.
You can connect devices to any safety input channel 
or combination of channels as needed.
We recommend that you connect even-numbered 
input points to even-numbered test output points 
and odd-numbered input points to odd-numbered 
test output points.
This wiring practice can maximize diagnostic 
independence and separation.

SA Power

Connections to an external power supply that 
provides SA power via the SA Power RTB on one of the 
following:
• Compact GuardLogix 5380 controller
• 5069-AENTR or 5069-AEN2TR EtherNet/IP Adapter
• 5069-FPD field potential distributor

IMPORTANT

: Remember the following:

• The 5069-IB8S and 5069-IB8SK modules use DC 

SA power. You must connect DC power to the 
component, that is, controller, adapter, or field 
potential distributor, that provides SA Power to 
the modules.

• If you install modules in a system that use AC SA 

power and DC SA power, you must install them on 
separate SA power buses.

• You use a 5069-FPD field potential distributor to 

establish a new SA Power bus in a system. SA 
Power buses are isolated from each other. To keep 
the modules on separate SA Power buses, 
complete the following steps.
1. Install the modules that use one type of SA 

power, for example DC, to the right of the 
adapter or controller, that is, the first SA 
Power bus.

2. Install the 5069-FPD field potential distributor 

to establish a second SA Power bus.

3. Install the modules that use the other type of 

SA power, for example AC, on the second SA 
Power bus.

Содержание 5069-IA16









































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды