background image

16 

 

dispensing of pellets stops and the flue gas motor and ambient fan are operating at maximum capacity in order to cool the 
oven as soon as possible. Minimal duration of the shutting off phase is 30 seconds, and the condition for the furnace to 
cool down completely is for the temperature of flue gases to be less than 68°C. 

 

4.5.8

 

OFF

 

In this state, the furnace is turned off i.e. no output on the furnace (flue gas motor, ambience fan, lighter and auger) is 

active. 

 

4.5.9

 

Block

 

The blockage condition occurs in the event of error or alarm. In the block mode, the fan of the exhaust gases, auger and 

lighters are off. To exit, hold P2 pressed for 3 seconds: if it is no longer blocked and there is no cause for alarm, the system 
will shut down. 

 

4.5.10

 

Ignition Recover

 

The furnace moves to this phase in two cases: 

5

 

If a power failure occurs during the operating mode and the flue gas temperature is higher than 50°C. 

6

 

Pressing the main switch at the moment when the furnace is in the shutting down phase. 

 
 

 

Other functions 

4.6.1

 

Voltage shortage management

 

 In the event of power failure, the system keeps the most important functional data. With the return of the voltage, the 

system assesses the saved data and: 

 

If the furnace is turned on and the temperature of the exhaust gases is higher than 50°C, the system switches to 

the Ignition recovery. By pressing the P1 button, a sudden new ignition of the system is possible. 

 

If the furnace is on, but the temperature of exhaust gases is less than 50°C, the system enters shutdown with 

error Er15

 

If the furnace is switched off or during shutting off or while blocked, the system returns to its previous state. 

 

In the absence of voltage over a period of one week, the system becomes blocked with an error message Er11 

indicating that the DATE / TIME is not accurate. Deblock using the P1 button, the value of TIME flashes, signalling the need 
for updating the TIME and DATE with the function CLOCK.

 

 

4.6.2

 

Pellet feeding calibration management 

 

The user has the possibility to calibrate the dosing of pellets in the User menu 1.  Calibration range from -7 ÷ 7. 1=5%. 

Each calibration of the pellet dosing is applied percentually to all work powers. E.g. if set to -1 then the pellet dosing would 
decrease by 5% in all operating modes (Power 1 - 5). 

Example 

Before 

calibration 

Power 1 = 

2.0 

Power 2 = 

3.0 

Power 3 = 

4.0 

Power 4 = 

5.0 

Power 5 = 6.0 

Step = -1 

Power 1 = 

1.9 

Power 2 = 

2.85 

Power 3 = 

3.8 

Power 4 = 

4.75 

Power 5 = 5.7 

Never calibrate the pellet dosing without consultations with the repair shop. 

 

4.6.3

 

Managing the correction of the  flue gas motor

 

The user has the possibility to calibrate the speed of flue gases motor in the User menu 1. Calibration range from -7 ÷ 7. 

1=5%.  Each  calibration  is  applied  percentually  to  all  work  powers.  E.g.  if  set  to  3  then  the  flue  gas  motor  speed  would 
increase by 15% (3x5%) in all operating modes (Power 1 - 5). 

Exampl

Before 

calibration 

Power 1 = 

1000 

Power 2 = 

1200 

Power 3 = 

1400 

Power 4 = 

1600 

Power 5 = 1800 

 

Step = +3 

Power 1 = 

1150 

Power 2 = 

1380 

Power 3 = 

1610 

Power 4 = 

1840 

Power 4 = 2070 

Never calibrate the speed of flue gas motor without consultations with the repair shop. 

 

4.6.4

 

Safety thermostat

 

In case the temperature of the pellets in the tank reaches a value greater than 90°C, a safety thermostat is activated in 

order to prevent the ignition of the pellets in the tank. The system moves to the blockage mode of work and the alarm 
message Er01 appears. 

 

 

4.6.5

 

Periodical cleaning of the furnace

 

When the system is in stable condition, after a specified time interval (every 45 minutes), the system automatically 

performs periodic cleaning for 30 seconds. 

During the periodic cleaning, the flue gas motor works with increased intensity and the dosing of pellets stops. 

 

Содержание LUCA S


























Отзывы: